manualshive.com logo in svg

Yamaha F9.92D, Owner'S Manual

Share
Download
Yamaha F9.92D Owner'S Manual Download Page 19

 

Basic components

 

14

 

tions.

 

EMU25830

 

Fuel joint

 

This joint is used to connect the fuel line.

 

EMU25841

 

Fuel gauge

 

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

 

EMU25850

 

Fuel tank cap

 

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

 

EMU25860

 

Air vent screw

 

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

 

EMU26180

 

Remote control

 

The remote control lever actuates both the
shifter and the throttle. The electrical switch-
es are mounted on the remote control box.

 

EMU26190

 

Remote control lever

 

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

 

1. Air vent screw
2. Fuel gauge
3. Fuel joint
4. Fuel tank cap

 

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed

Summary of Contents for F9.92D





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands