Yamaha F9.92D Owner'S Manual Download Page 82 | Manualshive

Page: 82 / 92

background image

Trouble Recovery

77

NOTE:

Consult your Yamaha dealer if the new fuse

immediately blows again.

EMU29520

Power trim and tilt will not operate

If the engine cannot be tilted up or down with
the power trim and tilt/ the power tilt because
of a discharged battery or a failure with the
power trim and tilt unit/the power tilt, the en-
gine can be tilted manually.
1.

Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.

2.

Put the engine in the desired position,
then tighten the manual valve screw by
turning it clockwise.

EMU29531

Starter will not operate

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

WARNING

EWM01020

●

Use this procedure only in an emergen-
cy and only to return to port for repairs.

●

When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not oper-
ate. Make sure the remote control lever
is in neutral. Otherwise the boat could
unexpectedly start to move, which
could result in an accident.

●

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the
cord where it could become entangled,
preventing it from functioning.

●

Avoid accidentally pulling the lanyard
during normal operation. Loss of en-
gine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the
boat to be thrown forward.

●

Be sure no one is standing behind you
when pulling the starter rope. It could
whip behind you and injure someone.

●

An unguarded, rotating flywheel is very
dangerous. Keep loose clothing and
other objects away when starting the
engine. Use the emergency starter rope
only as instructed. Do not touch the fly-
wheel or other moving parts when the
engine is running. Do not install the

1. Fuse holder
2. Fuse (20 A)
3. Spare fuse (20 A)

1. Manual valve screw

ZMU02092

1

2

3

«
...
80
81
82
83
84
...
»

Summary of Contents for F9.92D





























































































Reviews:

No comments

Related manuals for F9.92D

Brand: IEI Technology Pages: 177

Brand: Lantronix Pages: 10

Brand: Biostar Pages: 45

Brand: ON Semiconductor Pages: 20

Brand: JETWAY Pages: 46

Brand: Zida Pages: 28

Brand: Quantum Design Pages: 77

Brand: IBASE Technology Pages: 56

Brand: Supero Pages: 90

Brand: Global American Pages: 37

Brand: Gigabyte Pages: 93

PRESTIGE X570 CREATION

Brand: MSI Pages: 88

BeagleBone Black Proto Cape

Brand: sparkfun Pages: 4

Brand: SOLTEK Pages: 94

Brand: ASROCK Pages: 35

Brand: Microchip Technology Pages: 18

Brand: IBASE Technology Pages: 60

Brand: Acorp Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands