Yamaha F9.92D Owner'S Manual Download | Manualshive

Page: 36 / 92

background image

Operation

31

NOTE:

●

It is not necessary to use the choke when
starting a warm engine.

●

If the choke knob is left in the “

”

(start) position while the engine is running,

the engine will run poorly or stall.

5.

Pull the manual starter handle slowly un-
til you feel resistance. Then give a
strong pull straight out to crank and start
the engine. Repeat if necessary.

6.

After the engine starts, slowly return the
manual starter handle to its original po-
sition before releasing it.

7.

Slowly return the throttle grip to the fully
closed position.

NOTE:

●

When the engine is cold, it needs to be
warmed up. For further information, see
page 35.

●

If the engine does not start on the first try,
repeat the procedure. If the engine fails to
start after 4 or 5 tries, open the throttle a
small amount (between 1/8 and 1/4) and
try again. Also if the engine is warm and
fails to start, open the throttle a same
amount and try to start the engine again. If

the engine still fails to start, see page 73.

EMU27562

Electric start models

1.

Place the gear shift lever in neutral.

ZMU02355

ZMU02029

ZMU02030

ZMU01988

N

«
...
34
35
36
37
38
...
»

Summary of Contents for F9.92D





























































































Reviews:

No comments

Related manuals for F9.92D

Brand: IEI Technology Pages: 211

Brand: IEI Technology Pages: 8

Brand: IEI Technology Pages: 8

Brand: V2 ELETTRONICA Pages: 12

Brand: Qiyang Pages: 27

IP-M945A SERIES

Brand: WEALTHTEC Pages: 72

Brand: ST Pages: 79

Brand: MSI Pages: 76

Brand: JETWAY Pages: 56

Brand: MSI Pages: 104

Brand: JETWAY Pages: 39

Brand: Linear Technology Pages: 7

Brand: Gigabyte Pages: 96

Brand: JETWAY Pages: 56

Brand: Gigabyte Pages: 74

Brand: MSI Pages: 77

Brand: M-tech Pages: 2

Brand: u-blox Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands