Yamaha F9.92D Owner'S Manual Download Page 52

Page: 52 / 92

Operation

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

To return the outboard motor to the nor-
mal running position, press the power
trim / tilt switch and slowly tilt the out-
board motor down.

EMU28190

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to
prevent them from becoming clogged with
salt deposits.

NOTE:

For cooling system flushing instructions, see

page 51.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
if you use the outboard motor in turbid (mud-
dy) water conditions.

ZMU03525

ZMU01988

ZMU01935

ZMU02823

ZMU04900

Summary of Contents for F9.92D





























































































Search results

Summary of Contents for F9.92D

Reviews:

Related manuals for F9.92D

Brands by name

Popular brands

Yamaha F9.92D, Owner'S Manual

Search results

Summary of Contents for F9.92D

Reviews:

Related manuals for F9.92D

Brands by name

Popular brands