manualshive.com logo in svg

Yamaha F9.92D, Owner'S Manual

Share
Download
Yamaha F9.92D Owner'S Manual Download Page 6

 

1

 

General information

 

EMU25170

 

Identification numbers record

 

EMU25182

 

Outboard motor serial number

 

The outboard motor serial number is
stamped on the label attached to the port
side of the clamp bracket or the upper part of
the swivel bracket.
Record your outboard motor serial number in
the spaces provided to assist you in ordering
spare parts from your Yamaha dealer or for
reference in case your outboard motor is sto-
len.

 

EMU25190

 

Key number

 

If a main key switch is equipped with the mo-
tor, the key identification number is stamped
on your key as shown in the illustration.
Record this number in the space provided for
reference in case you need a new key.

 

EMU25220

 

Emission control information

 

EMU25230

 

North American models

 

This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for ma-
rine SI engines. See the label affixed to your
engine for details.

 

EMU25242

 

Approval label of emission control certif-
icate

 

This label is attached to the bottom cowling.
New Technology; (4-stroke/HPDI) EM

 

1. Outboard motor serial number location

 

1. Key number

1. Approval label location

1

ZMU04948

Summary of Contents for F9.92D





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands