Xinje DS2-45P5-A Reference Manual Download Page 2

Page: 2 / 43

►►

Safety caution



Confirmation when receive products



DO NOT install any driver which is damaged, lack of accessories or not the same

with the model ordered.



Installation



Cut off external power supply before installation.



Wiring



Cut off external power supply before wiring.



Connect AC power supply to the corresponding terminals.



Do not connect a three-phase power supply to the U, V, or W output terminals.



Use 2mm

wire to grounding the ground terminals.



Operation



Do not remove the panel cover while the power is ON.



Do not touch terminals for five minutes after the power has been turned OFF.



Do not connect with any motor when trial operation.



Before starting operation with a machine connected, change the settings to match

the parameters of the machine.



Do not attempt to change wiring while the power is ON.



Do not touch the heat sinks during operation.

►►

Checking Products upon Delivery

. When receive the products, please check below items:

Items

Comments

Are the delivered products the ones

that were ordered?

Check the model numbers marked on the nameplates

of the servomotor and servo drive.

Does the servomotor shaft rotate

smoothly?

The servomotor shaft is normal if it can be turned

smoothly by hand. Servomotors with brakes,

Summary of Contents for DS2-45P5-A












































Search results

Summary of Contents for DS2-45P5-A

Reviews:

Related manuals for DS2-45P5-A

Brands by name

Popular brands

Xinje DS2-45P5-A, Reference Manual

Search results

Summary of Contents for DS2-45P5-A

Reviews:

Related manuals for DS2-45P5-A

Brands by name

Popular brands