manualshive.com logo in svg

Xerox WorkCentre 5222, System Administration Manual

Share
Download
Xerox WorkCentre 5222 System Administration Manual Download Page 425

Fault Codes 

425

036-788
036-789

The polling feature was to be used, but the target machine did not store the 
documents to be polled. Check the target machine, and try again.

036-790
036-791

Communication failed due to an invalid request. Check the procedure in the 
User Guide and perform the operation again.

036-792
036-793

Refer to 034-508.

036-795

The remote copy function (to make multiple copies of a received document) is 
not supported on the destination machine. Check if the remote copy function is 
supported on the destination machine.

036-796

The general fax mode was used, because the remote copy function (to make 
multiple copies of a received fax document) was not supported on the 
destination machine. 

036-797
036-798
036-799

Refer to 034-508.

041-210
041-211

An error occurred in the tray module. Switch off the machine, and then switch it 
on again. Contact the Xerox Welcome Center if the problem persists.

047-211

A hardware problem occurred in the paper output assembly. Switch off the 
machine, and then switch it on again. Contact the Xerox Welcome Center if the 
problem persists.

047-212

An error occurred in the Offset Stacking Module. Switch off the machine, and 
then switch it on again. Contact the Xerox Welcome Center if the problem 
persists.

047-213

An error occurred in the Finisher. Switch off the machine, and then switch it on 
again. Contact the Xerox Welcome Center if the problem persists.

047-214

An error occurred in the Duplex Module. Switch off the machine, and then switch 
it on again. Contact the Xerox Welcome Center if the problem persists.

047-215

A communication error occurred between the main unit and the Exit Module. 
Switch off the machine, and then switch it on again. Contact the Xerox Welcome 
Center if the problem persists.

047-216

An error occurred in the Finisher. Switch off the machine, and then switch it on 
again. Contact the Xerox Welcome Center if the problem persists.

047-217

A communication error occurred between the main unit and the High Capacity 
Feeder. Switch off the machine, and then switch it on again. Contact the Xerox 
Welcome Center if the problem persists.

047-218

A communication error occurred between the main unit, and the Two Tray 
Module or the High Capacity Tandem Tray. Switch off the machine, and then 
switch it on again. Contact the Xerox Welcome Center if the problem persists.

062-210

The document feeder malfunctioned. Contact the Xerox Welcome Center.

062-211

An error occurred in the document feeder. Contact the Xerox Welcome Center.

062-277

A communication error occurred between the scanner and the feeder. Contact 
the Xerox Welcome Center.

062-394

Data could not be written in memory space. Switch off the machine, and then 
switch it on again. 

Code

Description and Remedy

Summary of Contents for WorkCentre 5222







































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands