Xerox Phaser 3428 User Manual Download

Page: 12 / 89

Rear view

control board cover

duplex unit

network port

power receptacle

USB port

power switch

parallel port

rear cover

optional tray 2 cable
connector

* The figure above shows an Phaser 3428/DN

with all available options.

Control panel overview

Stop

: Cancel an operation at any time.

Back

: Sends you back to the upper menu level.

Status

: Shows the status of your printer. See page 9.6.

Menu

: Enters Menu mode and arrows through the available

menus.

LCD

: Displays the printer status, error messages and menus

in progress.

Up Arrow

button: The option available in the selected menu

increase values.

: Confirms the selection on the display.

Down Arrow

button: The option available in the selected

menu decrease values.

Summary of Contents for Phaser 3428


























































































Search results

Summary of Contents for Phaser 3428

Reviews:

Related manuals for Phaser 3428

Brands by name

Popular brands

Xerox Phaser 3428, User Manual

Search results

Summary of Contents for Phaser 3428

Reviews:

Related manuals for Phaser 3428

Brands by name

Popular brands