Xerox Nuvera User Manual Download Page 58 | Manualshive

Page: 58 / 294

background image

Sheet Enhancement Module Specifications

• Height: 41.5 "
• Width: 14.25 "
• Depth: 28.25 "
• Weight: 168 lbs.

Sheet Retime Module (SRM)

The Sheet Retime Module (SRM) is a paper path timing module required to be installed only on 157 or
314 systems with a single Basic Finishing Module (a BFM, BFM Plus or a Direct Connect BFM).

The SRM is located before the BFM in the configuration. It enables BFM stapling capabilities and increases
the speed of the sheets as they enter the BFM. It provides the needed gap between prints for the BFM
to process sets at 157 or 314 ppm and staple sets at this full speed.

Note

Only A4/8.5 x 11 inch paper will run at the full 157 ppm or 314 ppm speed. Tab jobs and stock sizes less
than 8.2 inches (208mm) will run at reduced productivity.

Note

Small stock sizes less than 6.9 inches (175mm), such as A5 paper, cannot be run through the SRM.

Note

When running tab stock mixed with 8.5 x 11 in/A4 body stock enable the Improve Initial Pages
Registration within Set feature from Print Manager/Stacking area.

Xerox

®

Nuvera

®

6-12

User Guide and Training Aid (UGTA)

Xerox Nuvera EA/MX Production System

«
...
56
57
58
59
60
...
»

Summary of Contents for Nuvera







































































































































































































































































































Reviews:

No comments

Related manuals for Nuvera

Brand: DataCard Pages: 8

CLP 510N - Color Laser Printer

Brand: Samsung Pages: 270

Bixolon SRP-270

Brand: Samsung Pages: 13

Brand: Felix Storch Pages: 41

Brand: Xerox Pages: 9

Brand: Xerox Pages: 2

Brand: Xerox Pages: 8

Brand: Xerox Pages: 4

Brand: Xerox Pages: 150

Brand: Xerox Pages: 4

Brand: Xerox Pages: 6

Brand: Xerox Pages: 2

DocuPrint N2125

Brand: Xerox Pages: 246

DocuPrint N2025

Brand: Xerox Pages: 378

DocuPrint N2025

Brand: Xerox Pages: 176

DocuPrint C3290 FS

Brand: Xerox Pages: 240

Brand: Xerox Pages: 5

Brand: Xerox Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands