Xerox Nuvera User Manual Download Page 32 | Manualshive

Page: 32 / 294

Xerox Nuvera User Manual Download Page 32

Emergency Power Off

If any of the following conditions occur, immediately switch off the power to the machine and disconnect
the power cord from the electrical outlet. Call an authorized Xerox service representative to correct the
problem.

• The machine emits unusual noises or odors.
• The power cord is damaged or frayed.
• A wall panel circuit breaker, fuse, or other safety device is tripped.
• Liquid is spilled into the Xerox Nuvera Printer.
• The machine is exposed to water.
• Any part of the machine is damaged.

Electrical Supply

This product shall be operated from the type of electrical supply indicted on the product s data plate
label. If you are not sure that your electrical supply meets the requirements, please consult a licensed
electrician for advice.

Warning

This equipment must be connected to a protective earth circuit. This equipment is supplied with a plug
that has a protective earth pin. This plug will only fit into an earthed electrical outlet. This is a safety
feature. If you are unable to insert the plug into the outlet, contact a licensed electrician to replace the
outlet.

Caution

Always connect equipment to a correctly grounded power outlet. If in doubt, have the outlet checked
by a qualified electrician.

Disconnect Device

The power cable is the disconnect device for this equipment and is attached to the back of the machine
as a plug-in device. To remove all electrical power from the machine, disconnect the power cable from
the electrical wall outlet.

Laser Safety

North America

This product complies with safety standards and is certified as a Class 1 Laser product under the Center
for Devices and Radiological Health (CDRH) of the United States Food and Drug Administration (FDA)
implemented regulations for laser products. This product complies with FDA performance standards for
laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. These
regulations apply to laser products marketed in the United States. The label on the machine indicates
compliance with CDRH regulations and must be attached to laser products marketed in the United
States. This product does not emit hazardous laser radiation.

Xerox

®

Nuvera

®

3-6

User Guide and Training Aid (UGTA)

Safety and Certifications

«
...
30
31
32
33
34
...
»

Summary of Contents for Nuvera







































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands