Xerox Color C75 Press User Manual Download Page 258

Page: 258 / 340

3. While pressing the lever to the right, pull out the booklet staple cartridge unit.

4. Hold the tabs of the staple cartridge unit by the tabs and lift to remove it.

5. While holding the tabs of a new staple cartridge, push it into the unit.

6. Push the staple cartridge unit to its original position in the machine.

7. Close the Right Cover on the finisher.

Note

A message will display and the machine will not operate if the right cover is open
even slightly.

Xerox

Color C75 Press

17-10

User Guide

Standard/Booklet Maker Finisher

Summary of Contents for Color C75 Press





















































































































































































































































































































































Search results

Summary of Contents for Color C75 Press

Reviews:

Brands by name

Popular brands

Xerox Color C75 Press, User Manual

Search results

Summary of Contents for Color C75 Press

Reviews:

Brands by name

Popular brands