manualshive.com logo in svg

Xerox 770, User Manual, Page: 242 / 268

Share
Download
Xerox 770 User Manual Download Page 242

Note

Always refer to the SquareFold Trimmer Module Hints and Tips section before using the
SquareFold Trimmer Module. The hints and tips section provides valuable information
about setting up your jobs, which in turn ensures the best possible output for your
print/copy jobs.

You may want to run one or more test prints/copies before running larger jobs.

Identifying the components

Main components

The main components consist of:

1. Top Left Cover: Open this cover to remove paper jams. The square fold mechanism

is found in this area.

2. Top Right Cover: Open this cover to remove paper jams. The trimming mechanism

is found in this area.

3. Booklet Output Tray: This tray receives square-fold booklet output from the finisher.
4. Control Panel: The Control Panel consists of a mimic display, buttons, and various

indicator lights.

5. Trimmer Waste Container: Collects scrap/waste from the trimmer. Pull open to remove

and dispose of trimmer waste scraps.

Note

The top covers cannot be opened during normal operation or when the machine is idle.
The covers can be opened only when an indicator is lit and a jam/fault occurs within the
SquareFold Trimmer Module.

Xerox

®

 770 Digital Color Press

17-2

User Guide

SquareFold Trimmer Module

Summary of Contents for 770













































































































































































































































































Reviews:

No comments