manualshive.com logo in svg

Xerox 770, User Manual, Page: 187 / 268

Share
Download
Xerox 770 User Manual Download Page 187

Problem solving

General problems

HCS tampers no longer in contact with paper

Cause:  Problem occurs when printing with Clear dry ink/toner and using media that
is 120 gsm, coated, and large stock sizes (such as 12 x 18 in./304.8 x 457.2 mm).

Remedy:  Adjust the paper curl before printing the job. Refer to the System
Administration Guide for specific information on paper curl settings and adjustment.

Jam clearance

Tip

Always ensure that all paper jams, including any small ripped pieces of paper, are cleared
before proceeding with your print jobs.

Note

Remedies differ according to the paper jam location. Follow the instructions displayed
to remove the jammed paper.

HCS entrance jams (E1, E2, and E3)

Perform the following steps to clear the jam and resume printing:
1. Open the HCS Front Cover.

15-5

Xerox

®

 770 Digital Color Press

User Guide

High Capacity Stacker (HCS)

Summary of Contents for 770













































































































































































































































































Reviews:

No comments