manualshive.com logo in svg

Xerox 770, User Manual, Page: 181 / 268

Share
Download
Xerox 770 User Manual Download Page 181

Fault codes

The fault code table lists problems and suggested solutions that apply to the Interface
Module. If the problem persists after following all instructions, call your Xerox Customer
Support Center.

Recommended solution

Possible cause

Fault code

Paper jam:

048-100
048-101
048-102
048-103
048-900
048-901
048-903

• Open the front door.

• A jam occurred during

feeding.

• Carefully remove all sheets and paper

scraps from the jam clearance areas.

• A jam notification is

displayed on the UI.

• Close the front door. Verify the paper

used is within the approved paper
specifications.

Close the front door.

The front door is open.

048-300

Power off, then power on.

Decurler sensor or belt problem

048-310
048-311
048-312
048-313
048-314
048-315
048-316

Power off, then power on.

Cooling fan failure

048-317
048-318
048-319

Communication failure or
connection failure

048-320
048-321
048-322
048-324
048-325
048-326
048-327

• Check the connection between the

Interface Module and the connected
finishing device or devices.

• Fully clear any jams between the IM

and the connection finishing device or
devices.

• Ensure all jam clearance handles/levers

are returned to their closed positions.

• After clearing all jams, remove any

ejected paper fromthe finishing output
area.

• Power Off/On the machine.

14-9

Xerox

®

 770 Digital Color Press

User Guide

Interface Module

Summary of Contents for 770













































































































































































































































































Reviews:

No comments