manualshive.com logo in svg

Xerox 770, User Manual, Page: 196 / 268

Share
Download
Xerox 770 User Manual Download Page 196

Recommended solution

Possible cause

Fault code

Sensor fault

049 960
049 964

• Power Off/On the machine

• If the problem still exists, contact the

Customer Support Center.

Stacker height limit or full
detection fault

049 965
049 966

• Power Off/On the machine

• If the problem still exists, contact the

Customer Support Center.

HCS detects paper still
remaining on stacker cart
after the front door was
opened/closed.

049 967

• Open the HCS front door.

• Remove any paper from stacker cart.

• Close front door

• If necessary, power Off/On the

machine

• If the problem still exists, contact the

Customer Support Center.

Mix size, stacker full
detection fault

049 968

• Open the HCS front door.

• Remove any paper from stacker cart.

• Close front door

• If necessary, power Off/On the

machine

• If the problem still exists, contact the

Customer Support Center.

Stacker cart elevator motor
fault

049 969

• Open the HCS front door.

• Remove any paper from stacker cart.

• Close front door

• If necessary, power Off/On the

machine

• If the problem still exists, contact the

Customer Support Center.

Xerox

®

 770 Digital Color Press

15-14

User Guide

High Capacity Stacker (HCS)

(continued)

Summary of Contents for 770













































































































































































































































































Reviews:

No comments