Xerox 1235/DX - Phaser Color Laser Printer Advanced Features And Troubleshooting Manual Download Page 117 | Manualshive

Page: 117 / 144

background image

Advanced Features and Troubleshooting Manual

101

Using Printer Options

Using Printer Options

Installation Precautions

The Phaser 1235 Color Printer options are easy to install; however, before you attempt to
install (or remove) any printer options, please read and observe the following precautions.

Warning

TWO PEOPLE ARE REQUIRED WHEN LIFTING OR CARRYING THE PRINTER.
The printer should always be lifted and carried by two people, as shown below.
Exercise care in moving or relocating the printer, it is front-heavy and could tip
forward. Follow the recommended procedure when moving the printer from one
location to another. Refer to the Phaser 1235 Color Printer Setup Instructions.

Warning

DISCONNECT THE POWER CORD: Never remove the printer controller board
while the printer is plugged in. To avoid the possibility of electrical shock,
always disconnect the power cord when installing or removing ANY internal or
external printer option.

Warning

DISCHARGE STATIC ELECTRICITY: The controller board and internal printer
options (Hard Drive, Token Ring Card, Memory) are sensitive to static electricity.
Before installing or removing an internal option, discharge static electricity from
your body by touching something metal, such as the metal back plate on any
device plugged into a grounded power source. If you walk around before
finishing the installation, again discharge any static electricity.

51 kg

113 lbs.

«
...
115
116
117
118
119
...
»

Summary of Contents for 1235/DX - Phaser Color Laser Printer

















































































































































Reviews:

No comments

Related manuals for 1235/DX - Phaser Color Laser Printer

Brand: Labelmate Pages: 2

Brand: LabelTac Pages: 15

Brand: Xerox Pages: 16

7760DN - Phaser Color Laser Printer

Brand: Xerox Pages: 6

Brand: Synology Pages: 15

Brand: GCC Technologies Pages: 97

Brand: Rokit Pages: 21

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Fast T-Jet Blazer Pro

Brand: Screen Print & Inkjet Pages: 138

DocuPrint C2535 A

Brand: Xerox Pages: 120

Brand: Oki Pages: 32

bizhub press c1060

Brand: Konica Minolta Pages: 159

Brand: Oki Pages: 182

Brand: Epson Stylus Pages: 4

Brand: Axiohm Pages: 6

Brand: GCC Technologies Pages: 80

A1 with AMS lite

Brand: Bambu Lab Pages: 32

Brand: Ice Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands