Xerox 1235/DX - Phaser Color Laser Printer Advanced Features And Troubleshooting Manual Download Page 104

Page: 104 / 144

Phaser 1235 Network Color Printers

Troubleshooting

Supply Fan Error U9
Power Off/On

Fault

An error has been detected with the power

supply cooling fan. Turn off the printer, wait

15 seconds, then turn on the printer. If the

problem persists, check the support links at

www.xerox.com/officeprinting/1235support

Temp Sensor Error T29
Power Off/On

Fault

The temperature sensor is either not

communicating or reporting invalid data.

Turn off the printer, wait 15 seconds, then

turn on the printer. If the problem persists,

check the support links at

www.xerox.com/officeprinting/1235support

Toner Empty

[Black Toner Empty]
[Cyan Toner Empty]
[Magenta Toner Empty]
[Yellow Toner Empty]

Replace Toner

Fault

The toner cartridge has reached its end of

life. Install a new toner cartridge.

Toner Low

Black Toner Low
Cyan Toner Low
Magenta Toner Low
Yellow Toner Low

Attention

The level of toner in the toner cartridge is

low and should be replaced soon, as it is near

its end of life. Printing can continue until the

toner cartridge is empty; however, some

degradation of image quality may occur. The

message remains until interrupted by other

messages or until the toner cartridge is

replaced.

Toner Missing

[Black Toner Missing
[Cyan Toner Missing
[Magenta Toner Missing
[Yellow Toner Missing

Reseat Toner

Fault

The toner is either missing or requires

reseating to be recognized by the printer.

Reseat the toner. If that does not fix the

problem, turn off the printer, wait 15

seconds, then turn on the printer. If the

problem persists, check the support links at

www.xerox.com/officeprinting/1235support

Top Cover A Open
Close Top Cover A

Fault

The top cover (Cover A) is open. Close the

cover so that printing can continue.

Top Output Bin Full Remove
Prints

Fault

The top (face-down) bin is full and cannot

accept any more prints until it is emptied.

Once emptied, printing will continue where

it left off.

Transfer Belt Missing
Reseat Belt

Fault

The transfer belt is either missing or requires

reseating to be recognized by the printer.

Turn off the printer, make sure the transfer

belt is properly installed and turn on the

printer. If the problem persists, install a new

transfer belt. For further assistance, visit the

support links at

www.xerox.com/officeprinting/1235support

Front Panel Messages (cont'd.)

Message

Type

Explanation/Corrective Action

Summary of Contents for 1235/DX - Phaser Color Laser Printer

















































































































































Search results

Summary of Contents for 1235/DX - Phaser Color Laser Printer

Reviews:

Related manuals for 1235/DX - Phaser Color Laser Printer

Brands by name

Popular brands

Xerox 1235/DX - Phaser Color Laser Printer, Advanced Features And Troubleshooting Manual

Search results

Summary of Contents for 1235/DX - Phaser Color Laser Printer

Reviews:

Related manuals for 1235/DX - Phaser Color Laser Printer

Brands by name

Popular brands