Xerox 1235/DX - Phaser Color Laser Printer Advanced Features And Troubleshooting Manual Download Page 96

Page: 96 / 144

Phaser 1235 Network Color Printers

Troubleshooting

Warning

Avoid contact with the printer’s fuser rollers, which may be hot.

Make sure to observe the safety guidelines and recommendations provided in the Safety
Notes. See

Getting to Know Your Printer

on page 1.

If your printer is not operating properly, make sure that the following hardware and
software issues on page 80 have been considered.

Hardware

■

Is the printer plugged in?

■

Is the printer switched on?

■

Is the printer on-line?

■

Does the printer have proper clearance? For further information, refer to the

Getting to

Know Your Printer

on page 1.

■

Is the printer operating within the specified environmental conditions (temperature
and humidity)? For further information, refer to the

Getting to Know Your Printer

page 1.

■

Is the printer connected to a computer or network?

Software

■

Is the correct printer driver installed on the workstation?

■

Is your driver properly configured for the destination printer? For further information,
refer to

Printing

on page 23.

Summary of Contents for 1235/DX - Phaser Color Laser Printer

















































































































































Search results

Summary of Contents for 1235/DX - Phaser Color Laser Printer

Reviews:

Related manuals for 1235/DX - Phaser Color Laser Printer

Brands by name

Popular brands

Xerox 1235/DX - Phaser Color Laser Printer, Advanced Features And Troubleshooting Manual

Search results

Summary of Contents for 1235/DX - Phaser Color Laser Printer

Reviews:

Related manuals for 1235/DX - Phaser Color Laser Printer

Brands by name

Popular brands