Wood-mizer MK20-2 Installation & Operation Manual Download Page 15 | Manualshive

Page: 15 / 86

background image

Installation and Setup

Fan Module Installation

Installation and Setup

WMDKdoc020322

3-4

3

3.4

Fan Module Installation

In this installation process we will describe the process for a 20’ kiln with 4
modules.

NOTE:

All references to right and left are as viewing the kiln chamber from the door end.

CAUTION!

The fans can work at temperatures not exceeding 60

o

C

The fan module has already been pre-assembled at the factory and no further assembly is

required during the installation.

See Section 3.6

for instructions on how to connect the fan

modules to the control box.

Four (4) fan module units are required for a 20’ kiln.

First install the fourth module (marked “4” in the left bottom corner):



Drill holes for the module mounting strip in the chamber roof. Use two people to do
it. One person should place the module with bolted strip in the rear right hand corner
of the chamber and hold it in this position and the other person should drill through
the 5 holes into the roof. Remove the fan module and unbolt the module from the
strip. Re-position the strip to the roof and rivet the strip using the holes already
drilled. Now, position the fan module to the strip and bolt together.

NOTE:

You can

also drill the holes for the mounting strip using the dimensions indicated in figure
below.

FIG. 3-2

WDK033

Module no.

«
...
13
14
15
16
17
...
»

Summary of Contents for MK20-2























































































Reviews:

No comments

Related manuals for MK20-2

Pearl Dryer AC5011

Brand: Remington Pages: 68

Easy Fry Compact Digital

Brand: TEFAL Pages: 16

Brand: Linsar Pages: 12

Brand: Master Chef Pages: 18

Brand: Miele Pages: 56

Brand: Miele Pages: 13

Brand: Miele Pages: 80

Touchtronic T 1403

Brand: Miele Pages: 5

W 1213 WASHING MACHINE

Brand: Miele Pages: 56

Brand: Miele Pages: 88

TOUCHTRONIC T 8002

Brand: Miele Pages: 6

TOUCHTRONIC T 1303

Brand: Miele Pages: 86

Brand: Miele Pages: 100

Brand: Miele Pages: 100

TOUCHTRONIC T 8012 C

Brand: Miele Pages: 40

Brand: Miele Pages: 80

Brand: Miele Pages: 96

Brand: Miele Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands