Wood-mizer MK20-2 Installation & Operation Manual Download Page 17

Page: 17 / 86

Installation and Setup

Fan Module Installation

Installation and Setup

WMDKdoc020322

3-6



Drill the holes for the bottom rivets and rivet

the module to the side wall.

NOTE:

It is very important that the bottom part of the module is perpendicular to the side

wall (where the fans are mounted). Use a triangle to ensure that it is perpendicular to the
wall.

Use the same procedure as described above to mount the third, the second and the first
modules.

Place the fan module cables on the support trays properly. All the fan modules cables
need to be later connected to the outside control box.

There may be a length of clear wall between the last fan module and the inside face of the
closed kiln door. If so, it will be necessary to use a Plenum Blanking Kit to fill this gap.

See

Section 3.5

for plenum blanking kit installation instructions.

FIG. 3-5

If you are installing in a room other than a container, use wood screws or concrete mounting dowels.

Summary of Contents for MK20-2























































































Search results

Summary of Contents for MK20-2

Reviews:

Related manuals for MK20-2

Brands by name

Popular brands

Wood-mizer MK20-2, Installation & Operation Manual

Search results

Summary of Contents for MK20-2

Reviews:

Related manuals for MK20-2

Brands by name

Popular brands