Wood master FORCE 30 User Manual Download

Page: 3 / 44

Force 30 Owners Manual

2015

• Read and follow these directions carefully. Retain this manual for as long as you own your furnace.

• All installation and operations must follow STATE and LOCAL CODES for wiring, and firing of this

unit. These CODES may differ from this manual. Installation must be performed by a qualified installer.

•

Follow the manual carefully. Follow the recommended cleaning and maintenance.

• Never open the access doors during operation!

• Never operate any part of the furnace or system with covers, shields or panels removed.

• Anyone who is not familiar with and/or has not been trained to operate the furnace may not

operate the system. Only responsible adults should operate your furnace. If the furnace is not fired

properly damage could result and the warranty may be voided.

• Never allow children to play near or tamper with the furnace, fuels/fuel tank or any other part of the system.

• Always keep the area around and in front of the furnace clean and free from combustible materials.

• Keep animals away from the furnace.

• The operation may not be continued or restarted in the event of visible damages (for example, thermal

distortion, traces of smoke or fire, mechanical damages, etc.). Any damages must be repaired. In

the event of any doubts, please contact your authorized WoodMaster Dealer.

• The furnace system must not be exposed to external mechanical stress (for example, as storage, climbing

support, brace, or similar). This also applies for single parts (doors, covers, etc.).

• During operation only touch the PLC Temperatures at other points (for example, chimney, access

doors, ducting...) can be very high.

• The Force 30 must be operated exclusively according to the guidelines for planning, assembly,

regulations, statutes and product related instructions. The manufacturer is not liable for damages and

their results, if they occurred due to improper assembly, operation, application and also inadequate

maintenance and cleaning.

• Do not connect this unit to a chimney flue serving another appliance. Follow all state/local codes.

• Ensure that the burner is inserted to the maximum depth of the furnace. Check this each time the

burner is removed for cleaning or servicing.

• After installation the exhaust must be tested with an O2 sensor from dealer for a flue gas analysis.

Safety

Summary of Contents for FORCE 30













































Search results

Summary of Contents for FORCE 30

Reviews:

Related manuals for FORCE 30

Brands by name

Popular brands

Wood master FORCE 30, User Manual

Search results

Summary of Contents for FORCE 30

Reviews:

Related manuals for FORCE 30

Brands by name

Popular brands