background image

25

Force 30 Owners Manual

2015

12. 

The error “FUEL FAULT” can be displayed for multiple 

issues:

  1.  Make sure there are pellets in the pellet hopper.
  2.  Make sure that the auger drive motor is working by 

    connecting the power cord of the burner and the 

   power cord of the auger.

  3.  If the pellet hopper is empty it is best to fill and 

    run the auger until pellets come again manually. 

    Let the auger run for approx. 10 -15 min to get an 

    even dosage.
  4.  Make sure the pellets in the pellet hopper are 

    not cavatating. If this is occurring, clean the pellet 

   hopper.

If the problem persists, contact your dealer or Northwest 

Manufacturing, Inc. See the trouble shooting section for 

further assistance.

11. 

Error on the ignition element. This may be caused by an 

incorrect start dose, a dirty burner or a failed igniter. Turn off 

the burner and restart. Check to make sure you have the cor

-

rect start dose settings, or check the connection for the feed 

auger. If the burner starts, no further action is needed. If not 

see the troubleshooting section for further assistance. If the 

problem persists or if the igniter is bad, contact your dealer 

or Northwest Manufacturing, Inc.

Operation

13. Shutting the Burner Off

When shutting off the burner, either for maintenance or for the end of the season, the burner must be allowed 

to enter and complete its shutdown process. Failure to allow the burner to shut down properly can result in 

damage to the burner, especially if done repeatedly. It will also greatly reduce the burners efficiency.  If the 

burner is idle and the combustion fan is off, the burner can be switched off.

If the burner is running, either wait for the thermostat reaches its set point to switch the burner off, or lower 

the thermostat to switch the burner off. Once the air clean occurs and the combustion fan stop, shut off power 

to the burner and allow to cool before cleaning. 

Menu/Ok

FUEL FAULT

V18

1

2

3

4

Menu/Ok

IGNITION FAULT

V18

1

2

3

4

Summary of Contents for FORCE 30













































Reviews: