background image

443 06 4002 00   

Mar. 2013

Specifications  subject to change without notice.

NAHA00101MH

INSTALLATION  INSTRUCTIONS

MANUFACTURED (MOBILE) HOME KIT

Condensing Gas Furnace Conversion

C E RT I F I E D

NOTE

:  Read the entire instruction manual before starting the

installation.

SAFETY CONSIDERATION

!

WARNING

FIRE, EXPLOSION, ELECTRICAL SHOCK, AND CARBON

MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury or

death.
This conversion kit shall be installed by a qualified service

agency in accordance with the manufacturer’s instructions

and all applicable codes and requirements of the authority

having jurisdiction. If the information in these instructions is

not followed exactly, a fire, explosion, or production of carbon

monoxide could result causing property damage, personal

injury, or loss of life. The qualified service agency is

responsible for the proper installation of this furnace with this

kit. The installation is not proper and complete until the

operation of the converted appliance is checked as specified

in the manufacturer’s instructions supplied with the kit.

!

AVERTISSEMENT

LE FEU, L’EXPLOSION, CHOC ELECTRIQUE, ET

MONOXYDE DE CARBONE EMPOISONNER

Cette trousse de conversion doit être installée par un servie

d’entretien qualifié, selon les instructions du fabricant et selon

toutes les exigences et tous les codes pertinents de l’autorité

compétente. Assurezvous de bien suivre les instructions

dans cette notice pour réduire au minimum le risque

d’incendie, d’explosion ou la production de monoxyde de

carbone pouvant causer des dommages matériels, de

blessure ou la mort. Le service d’entretien qualifié est

responsable de l’installation de cette trousse. L’installation

n’est pas adéquate ni complète tant que le bon

fonctionnement de l’appereil converti n’a pas été vérfié selon

les instructions du fabricant fornies avec la trousse.

Installing and servicing heating equipment can be hazardous

due to gas and electrical components. Only trained and

qualified personnel should install, repair, or service heating

equipment.
Untrained personnel can perform basic maintenance functions

such as cleaning and replacing air filters. Trained service

personnel must perform all other operations. When working on

heating equipment, observe precautions in the literature, on

tags, and on labels attached to or shipped with the unit, and

other safety precautions that may apply.
Follow all safety codes. In the United States, follow all safety

codes including the current edition of the National Fuel Gas

Code (NFGC) NFPA No. 54/ANSI Z223.1. In Canada, refer to

the current edition of the National Standard of Canada, Natural

Gas and Propane Installation Codes (NSCNGPIC),

CAN/CSA

B149.1 and .2. Wear safety glasses and work

gloves. Have a fire extinguisher available during start

up,

adjustment steps, and service calls.
Recognize safety information. This is the safety

alert symbol

. When you see this symbol on the furnace and in

instructions or manuals, be alert to the potential for personal

injury. Understand the signal words DANGER, WARNING,

CAUTION and NOTE. The words DANGER, WARNING, and

CAUTION are used with the safety alert symbol. DANGER

identifies the most serious hazards which 

will 

result in severe

personal injury or death. WARNING signifies a hazard which

could 

result in personal injury or death. CAUTION is used to

identify unsafe practices which 

may 

result in minor personal

injury or product and property damage. NOTE is used to

highlight suggestions which 

will 

result in enhanced installation,

reliability, or operation.

INTRODUCTION

!

WARNING

FIRE, EXPLOSION, ELECTRICAL SHOCK AND CARBON

MONOXIDE POISONING HAZARD

Failure to follow instructions could result in personal injury,

death or property damage.
Improper installation, adjustment, alteration, service,

maintenance, or use can cause carbon monoxide poisoning,

explosion, fire, electrical shock, or other conditions, which

could result in personal injury or death. Consult your

distributor or branch for information or assistance. The

qualified installer or agency must use only factory

authorized

kits or accessories when servicing this product.

!

WARNING

FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury,

death or property damage.
Gas supply MUST be shut off before disconnecting electrical

power and proceeding with conversion.

This instruction covers the installation of kit Part No.

NAHA00101MH in the following gas furnaces for manufactured

(mobile) home applications.
This kit is only for use in single stage 40,000 through 120,000

Btuh gas input models when installed as a direct vent (2

pipe)

furnace.

NOTE

:  This kit is not approved for the 140,000 Btuh gas input

model furnace, any two

stage and variable speed models, any

non

direct vent (1

pipe) applications nor any furnace that does

not have a sealed combustion system with provisions for

outside air.

40,000 to 120,000 BTUH MODEL NUMBERS

BEGINNING WITH:

G9MXE

F9MXE

N9MXB

N9MSB

N9MSE

Summary of Contents for NAHA00101MH



















Reviews: