WOLFF 163317 Translation Of The Original Instruction Download Page 15

15

d)  Do not abuse the cord. Never use the cord for
 

carrying, pulling or unplugging the power tool.

 

Keep cord away from heat, oil, sharp edges and

 

moving parts.

 

Damaged or entangled cords increase the risk of

 

electric shock.

e)   When operating a power tool outdoors, use an
 

extension cord suitable for outdoor use.

 

The use of a cord suitable for outdoor use reduces

 

the risk of electric shock. 

 

The machine is to be carried exclusively by the carry 

 

ing handle Fig. pos. 11.

 

If the power cord of this device is damaged, it must be  

 

replaced by the manufacturer or its customer service or  

 

a similarly qualifi ed person in order to avoid hazards.  

 

avoid hazards.

f)   If the operation of a power tool in a damp location  
 

is unavoidable, use a residual current device (RCD)  

 

protected supply.

 

The use of an RCD reduces the risk of electric shock.

3)  Personal safety

a)  Stay alert, watch what you are doing and use
 

common sense when operating a power tool.

 

Do not use a power tool while you are tired or

 

under the infl uence of drugs, alcohol or

 

medication.

 

A moment of inattention while operating power tools

 

may result in serious personal injury.

b)  Use personal protective equipment. Always   

 

 

wear eye protection. 

 

 

Protective equipment such as dust mask, non-slip   

 

safety shoes and hearing protection used for   

 

 

appropriate conditions will reduce personal injuries.  

4)  Power tool use and care  

a)   Do not force the power tool. Use the correct     
 

power tool for your application. 

 

 

The correct power tool will do the job better and     

 

safer at the rate for which it was designed.  

b)  Do not use the power tool if the switch does not   

 

turn it on and off .  

 

Any power tool that cannot be controlled with the    

 

switch is dangerous and must be repaired.  

c)   Disconnect the plug from the power source and/ 
 

or the battery pack from the power tool before   

 

making any adjustments, changing accessories, or  

 

storing power tools.  

 

Such preventive safety measures reduce the risk of  

 

starting the power tool accidentally.  

d)  Store idle power tools out of the reach of children  
 

and do not allow persons unfamiliar with the power  

 

tool or these instructions to operate the power tool.  

 

Power tools are dangerous in the hands of untrained  

 

users. 

e)   Maintain power tools. Check for misalignment or   
 

binding of moving parts, breakage of parts and   

 

any other conditions that may aff ect the power   

 

tool’s operation.  

 
 

If damaged, have the power tool repaired before use.  

 

Many accidents are caused by poorly maintained    

 

power tools.  

f)   Keep cutting tools sharp and clean.  

 

Properly maintained cutting tools with sharp cutting   

 

edges are less likely to bind and are easier to control.  

g)  Use the power tool, accessories and tool bits etc.  
 

in accordance with these instructions, taking into  

 

account the working conditions and the work to be  

 

performed.  

 

Use of the power tool for operations diff erent from   

 

those intended could result in a hazardous situation. 

5) Service

 

a)  

Have your power tool serviced by a qualifi ed     

 

repair person using only identical replacement   

 

parts.  

 
 

This will ensure that the safety of the power tool is   

 

maintained.  

EN

Summary of Contents for 163317





























Reviews: