Wiznet W7500S2E-R1 User Manual Download Page 31

Page: 31 / 47

W7500S2E-R1 serial to Ethernet module

W7500S2E-R1 user manual

Note: If W7500S2E-R1 works on TCP server mode, HTTP port should be the difference to the local port.

6.4.3.19

Remote host domain name (AT+DOMAIN)

Command format

Parameters

Usage

AT+DOMAIN=<domain>\r\n <domain>

Remote host domain name

default: www.iwiznet.cn

Define new value

AT+DOMAIN?\r\n

Query current value

Return value

[DOMAIN] Value is: <domain>\r\nOK\r\n

This command sets the remote domain name, so please do not enter IP address format to this command. This

command requires “AT+DNSEN” command to analysis DNS domain name. This command will only available

on TCP client and UDP modes.

6.4.3.20

DNS enable (AT+DNSEN)

Command format

Parameters

Usage

AT+DNSEN=<dns>\r\n

<dns>

0: Disable DNS function (default)

1: Enable DNS function

Define new value

AT+DNSEN?\r\n

Query current value

Return value

[DNSEN] Value is: <dns>\r\nOK\r\n

After enable DNS function, W7500S2E-R1 can use remote host through domain name. Every time the module

has power up, it activates DNS function. This command will only available on TCP client and UDP modes.

6.4.3.21

Reconnect time (AT+RECONTIME)

Command format

Parameters

Usage

AT+RECONTIME=<time>\r\n

<time>

Reconnect time, default: 0

Define new value

AT+RECONTIME?\r\n

Query current value

Return value

[RECONTIME] Value is: <time>\r\nOK\r\n

This command configures to limit the time of the TCP client waiting for reconnection the module has

disconnected from a TCP server. This command will only available on TCP client mode. Default value is 0 for

direct reconnection. Value range is 0 to 60,000. Unit: ms.

6.4.3.22

NetBIOS (AT+NETBIOS)

Command format

Parameters

Usage

AT+NETBIOS=<netbios>\r\n

0: Disable NetBIOS function (default)

1: Enable NetBIOS function

Define new value

AT+NETBIOS?\r\n

Query current value

Return value

[NETBIOS] Value is: <netbios>\r\n

After enable NetBIOS function, user could use web browser to search the module by entering “http: //[device

name]” for visiting WIZS2E module configuration web page.

Note: To use this function, the Device Name cannot consist entirely of digits, and the hyphen ("-") or full-stop

(".") characters may not appear as the first or last character or the same as other devices. The maximum length is

Summary of Contents for W7500S2E-R1
















































Search results

Summary of Contents for W7500S2E-R1

Reviews:

Related manuals for W7500S2E-R1

Brands by name

Popular brands

Wiznet W7500S2E-R1, User Manual

Search results

Summary of Contents for W7500S2E-R1

Reviews:

Related manuals for W7500S2E-R1

Brands by name

Popular brands