manualshive.com logo in svg

Wiznet W7500S2E-R1, User Manual

Share
Download
Wiznet W7500S2E-R1 User Manual Download Page 2

W7500S2E-R1 serial to Ethernet module 

W7500S2E-R1 user manual 

 

Document Revision History

 

 

 

 

 

Copyright notice 

Copyright © WIZnet H.K. Ltd. All rights reserved.   

Contact E-mail: 

[email protected]

   

For more information, please visit: 

http: //www.wiznet.com.hk/

 

V1.0 

2017-09-19  First release   

V1.1 

2018-05-30 

1.

 

Description of AT+NETBIOS command is revised 

2.

 

Parameters of AT+C1_STOPB command is changed to 0:1, 1:2 

3.

 

Maximum length of the AT+C1_SER_T command parameter is changed to 5, value 
range is changed to 0~60000 

4.

 

Parameter of the Terminal check (AT) query command is removed 

5.

 

Replace all "

/n/r

 " in the text with "

\r\n

" 

6.

 

Maximum length of the AT+C1_BIND command parameter is changed to 1 

7.

 

Maximum length of the AT+C1_TCPAT command parameter is changed to 3 

8.

 

Description of the AT+NAME command is updated 

9.

 

Chapter 2.2: Pin 2 of SW3 description in changes from GND to Vcc; picture has also 
been modified 

10.

 

Updated Figure 2-4 Evaluation Board Reference Design Schematic 

11.

 

Maximum length of the AT+MAC command parameter is removed 

12.

 

Stop Bit is changed to 1, 2 in the specification 

13.

 

Power supply is changed to DC 3.3V in the specification 

14.

 

Chapter 1.2.2: "upper and lower parts" is changed to "left and right" 

15.

 

Chapter 7.2: Baud Rate and Stop Bit is revised 

16.

 

Chapter 7.3: Device Name has maximum length 15 bytes 

17.

 

Chapter 7.4: Password has maximum length 15 bytes 

18.

 

Power supply is changed to DC 3.3V 

19.

 

Maximum length of the AT+DEFAULT and AT+RESET command parameters in the 
list of AT commands is modified to 15 

20.

 

Default value of AT+DEBUGMSGEN parameter is modified to 1 

21.

 

Chapter 5.3, WIZS2E ConfigTool new function introduction is added 

22.

 

All WIZS2E ConfigTool screen captures are updated 

Summary of Contents for W7500S2E-R1
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands