Wisenet XRN-410S User Manual Download Page 69

Page: 69 / 96

Channel Setup

You can configure the video settings for each channel.

Storage Device

You can check and change the settings related to the data storage device.

Device/Format

You can check a storage device, amount of use, type of use
and status of storage device.

•

ARB : Video that was not recorded due to disconnection from
the camera can be backed up after the connection with the
camera is re-established.
Press the button and an <

Auto Recovery Backup

> window

is opened.
For more information about settings, please refer to "

Device/

Format

". (Page 37)

HDD Alarm

You can set the alarm output port and the duration in case an
error occurs.

Monitor

You can configure the monitoring screen settings and set the
output system.

If the video is not played properly, refer to the troubleshooting
section later in this manual. (Page 82)

The Monitor Setup settings control the monitor connected to the
NVR.

Text

Device

Relevant values of a device connected to NVR can be set.

Event

It is possible to set total amount conditions and keywords to
display events of a text device.

English

_69

● SETUP VIEWER

Summary of Contents for XRN-410S

































































































Search results

Summary of Contents for XRN-410S

Reviews:

Related manuals for XRN-410S

Brands by name

Popular brands

Wisenet XRN-410S, User Manual

Search results

Summary of Contents for XRN-410S

Reviews:

Related manuals for XRN-410S

Brands by name

Popular brands