Winterthur Instruments AG CoatMaster Manual Download Page 75

Page: 75 / 86

Operation Manual CoatMaster

74/83

8.4

Filter pads

Visually inspect the filter pads regularly. When they are contaminated, they need cleaning.
For this purpose, proceed as follows:

•

Unscrew the two screws on the rear of the device (see figure).

Figure 14:

CoatMaster – Rear view

•

Remove the filter cover.

•

Take off the filter pads and clean them with compressed air.

•

If the filter pads are highly contaminated, they need to be replaced.

•

Remount the filter cover.

8.5

Clean or exchange filter pads for the CoatMaster Inline

If filter pads are installed within the rack, visually inspect them regularly. When they are contaminat-‐
ed, they need cleaning. For very strong contamination an exchange is necessary.

Summary of Contents for CoatMaster























































































Search results

Summary of Contents for CoatMaster

Reviews:

Related manuals for CoatMaster

Brands by name

Popular brands

Winterthur Instruments AG CoatMaster, Manual

Search results

Summary of Contents for CoatMaster

Reviews:

Related manuals for CoatMaster

Brands by name

Popular brands