Winterthur Instruments AG CoatMaster Manual Download Page 78 | Manualshive

Page: 78 / 86

background image

Operation Manual CoatMaster

77/83

9.3

Error and warning icons with their corrective measures

Icon

Meaning

Corrective measure

Warning icon
Measurement deviates signif-‐
icantly from the used applica-‐
tion

Make sure that the correct application is used for
measurement and the sample corresponds to the one
used for the applicaton development. Repeat the
measurement.

Error icon
Measurement value deviates
too much from the used ap-‐
plication

Make sure that the correct application is used for
measurement and the sample corresponds to the one
used for the applicaton development. Repeat the
measurement.

9.4

Additonal error and warning icons with their corrective measures for the
CoatMaster Inline

Icon

Meaning

Corrective measure

Warning icon
Coolant temperature too
high

Switch off the CoatMaster and wait for about half an
hour for the device to cool down. When the warning
persists, contact Winterthur Instruments.

Error icon
Coolant temperature critical

Switch off the CoatMaster and wait for about half an
hour for the device to cool down. When the error
persists, contact Winterthur Instruments.

Warning icon
Coolant flow too low

Make sure the tube connections are intact and that
their are no kinks in the tubes. When the warning
persists, contact Winterthur Instruments.

Error icon
Coolant flow critical

Make sure the tube connections are intact and that
their are no kinks in the tubes. When the error per-‐
sists, contact Winterthur Instruments.

«
...
76
77
78
79
80
...
»

Summary of Contents for CoatMaster























































































Reviews:

No comments

Related manuals for CoatMaster

Brand: AR Pages: 20

Brand: BANTE inststruments Pages: 15

Brand: 3Bays Pages: 21

Brand: Keller Pages: 6

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Brand: ICS Pages: 2

Brand: CAISSON Pages: 5

Brand: R.M. Young Pages: 2

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Brand: M-system Pages: 13

Brand: Maico Pages: 27

Brand: Magnescale Pages: 14

Brand: Underground Magnetics Pages: 48

Brand: A&D Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands