Winterthur Instruments AG CoatMaster Manual Download Page 34

Page: 34 / 86

Operation Manual CoatMaster

33/83

Wait after signal received before measuring (s)

: Time between the sensor signal is received until the

measurment is started

Wait between two measurements (s)

: Time between the individual measurements on the same

object

Number of measurements after trigger signal

: Number of measurements on the same object

Measure timeout (s)

: Wenn the measurement takes longer than this period, it is aborted

Trigger measurement all n trigger signals

: Measurement is triggered all n sensor signals

The connection of the external sensor to the CoatMaster is done via a standard 15 V interface pro-‐
vided with an XLR-‐connector (position 2 in figure 9).

The sensor connection has the following pin assignment:

Figure 11:

Connection external sensor to CoatMaster: 1 GND, 2 +15 V Supply, 3 Signal.

Summary of Contents for CoatMaster























































































Search results

Summary of Contents for CoatMaster

Reviews:

Related manuals for CoatMaster

Brands by name

Popular brands

Winterthur Instruments AG CoatMaster, Manual

Search results

Summary of Contents for CoatMaster

Reviews:

Related manuals for CoatMaster

Brands by name

Popular brands