Winterthur Instruments AG CoatMaster Manual Download Page 79

Page: 79 / 86

Operation Manual CoatMaster

78/83

Icon

Meaning

Corrective measure

Warning icon
Coolant level too low

Refill coolant into the Water supply, see section 9.4.
When the warning persists, contact Winterthur In-‐
struments.

Error icon
Coolant level critical

Refill coolant into the Water supply, see section 9.4.
When the error persists, contact Winterthur Instru-‐
ments.

Notification
Maintenance due soon

Contact Winterthur Instruments for a service date.

Notification
Maintenance due now

Contact Winterthur instruments for a service date as
soon as possible. A further operation of the device
while the notification is persisting may lead to device
damage.

Error
Server / client connection
failed

Check for the correct IP address and make sure, the
server is running. If necessary, download a new client
version in the Web Client under Downloads.

Summary of Contents for CoatMaster























































































Search results

Summary of Contents for CoatMaster

Reviews:

Related manuals for CoatMaster

Brands by name

Popular brands

Winterthur Instruments AG CoatMaster, Manual

Search results

Summary of Contents for CoatMaster

Reviews:

Related manuals for CoatMaster

Brands by name

Popular brands