Winterthur Instruments AG CoatMaster Manual Download Page 73 | Manualshive

Page: 73 / 86

background image

Operation Manual CoatMaster

72/83

8

Maintenance / Service

Use only genuine Winterthur Instruments consumables and   genuine spare parts for maintenance and
repair   to assure good system performance and reliability. Any modifications to the spare parts used
are   only allowed with the   prior written permission of Winterthur Instruments.

8.1

General

WARNING

Risk of burns by electric current.

Serious injuries or death can result.

Prior to any maintenance and service, switch off the device and unplug the mains cable.

Do not open the housing of the CoatMaster. Exception: Unmounting the the rear cover for cleaning
or exchanging the filter pads (see section 7.3). This is also valid when the CoatMaster is not connect-‐
ed to the mains. Opening the CoatMaster will void any liability and annuls the guarantee.

Put the   CoatMaster into operation at least once every six months.
After 500.000 measurements or one year (also   if the device is not in   use) the CoatMaster has to   be
serviced by a Winterthur Instrument service engineer.

The Desktop Client software monitors the replacement parts of   the CoatMaster. As soon as the state
of a replacement parts becomes critical or it has reached   or exceeded   its intended   operating margin,
a   corresponging message   is displayed.

Notification icon
Maintenance due soon

Is displayed below the measurement value, when a
maintenance of the device is due soon

Notification icon
Maintenance due now

Is displayed below the measurement value, when a
maintenance of the device is due now

8.2

Measurement window

Clean   the measurement window from any contamination by oil-‐free compressed air   to assure good
CoatMaster performance and   reliability.
Stubborn contamination can be   removed with the   soft, lint-‐free cloth and alcohol (e.g. eyeglass
cleaning cloth).

«
...
71
72
73
74
75
...
»

Summary of Contents for CoatMaster























































































Reviews:

No comments

Related manuals for CoatMaster

Brand: Lumel Pages: 32

Brand: Oceanic Pages: 152

Brand: Kaiterra Pages: 8

Brand: Kaiterra Pages: 12

Brand: MadMan Pages: 37

Brand: MADDALENA Pages: 5

Brand: WalkLAB Pages: 16

Portable Grand DGX-670

Brand: Yamaha Pages: 93

Portatone PSR-410

Brand: Yamaha Pages: 65

Brand: Zeversolar Pages: 35

Brand: Zenner Pages: 52

Brand: OBD Pages: 5

Brand: AEMC Pages: 4

Brand: Palstar Pages: 37

Brand: LD Didactic Pages: 2

Brand: Sur-Gard Pages: 12

Brand: Solinst Pages: 2

Brand: Bitzer Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands