background image

2

60706-211/J

TABLE OF CONTENTS

SAVE THESE INSTRUCTIONS 

2

SAFETY 3

SPECIFICATIONS 4

GENERATOR
ENGINE

INTRODUCTION 5

TESTING POLICY
PRODUCT DESCRIPTION

PREPARING THE UNIT 

6

UNPACKING

INSTALLATION 7

GENERATOR CLEARANCES
ENGINE-GENERATOR SET MOUNTING
FUEL INSTALLATION
LIQUID PROPANE VAPOR (LP)
NATURAL GAS (NG)
FUEL PRESSURE
FUEL PRESSURE TABLES
NG/LP FUEL CONVERSION
LUBRICATION
OIL RECOMMENDATIONS
OIL ALERT SYSTEM

INSTALLING THE BATTERY 

11

SERVICING BATTERIES
BATTERY CHARGING
BATTERY CHARGER
SOLAR CHARGER OPTION

AC ELECTRICAL CONNECTIONS 

13

GENERATOR CONNECTIONS
WINCO UL ATS (ASCO 185)

DC ELECTRICAL INTERCONNECTION  14

ASCO 185 UL SWITCH

INITIAL START UP 

15

START UP PROCEDURE
CUSTOMER CONNECTION AREA

SEQUENCE OF OPERATION 

18

DSE 3110 

19

FRONT PANEL CONFIGURATION
ACCESSING THE FRONT PANEL
EDITING A PARAMETER
DSE 3110 FAULT CODES
DSE 3110 ENGINE CONTROL
MODULE DISPLAY

PREVENTATIVE MAINTENANCE 

21

AUTOMATIC TRANSFER SWITCH
ENGINE-GENERATOR SET
ENGINE MAINTENANCE
MAINTENANCE SCHEDULE

TROUBLESHOOTING 22

OUTLINE DRAWING 

23

PAD LAYOUT DRAWING 

24

AC WIRING SCHEMATIC 

24

AC AND DC GENERATOR SCHEMATIC 25

SOLAR CONTROL PANEL 

26

EXTERNAL RECEPTACLE ASSEMBLY  26

SOLAR PANEL ASSEMBLY 

27

24 MONTH LIMITED WARRANTY 

28

LIMITED WARRANTY 

28

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should 

be followed during installation and maintenance of the 

generator. Read and understand all instructions in the 

manual before starting and operating the generator.

USING THIS MANUAL

Congratulations on your choice of a WINCO generator. 

You have selected a high-quality, precision-engineered 

generator designed and tested to give you years of 

satisfactory service.

To get the best performance from your new generator, it is 

important that you carefully read and follow the operating 

instructions in this manual.

Should you experience a problem please follow the 

“Troubleshooting Tables” near the end of this manual. 

The warranty listed in the manual describes what you can 

expect from WINCO should you need service assistance in 

the future.

Summary of Contents for PSS8B2F





























Reviews: