51
It is easy to use the throttle cut function to shut
down the engine. It is only necessary to toggle a
switch in the idle down state to achieve engine cut or
motor stall. After the throttle cut function is enabled,
the throttle cut or the ESC's fully flameout position
can be adjusted. After the function is activated,
regardless of the throttle lever position, the throttle
output remains at the set position. The flameout
function does not start in the high speed throttle
state, avoiding erroneous operation. For safety
reasons, it is recommended to set the throttle cut
function.
Note:
After the throttle cut function is enabled, the
function is turned off again. The throttle action
determines that the stick has no power output when
it is in the high position. Only when the oil level (gear
position) is increased from the low position of the
throttle, the normal throttle output can be restored!
Enter the interface:
→ Model Menu→
WFLY
Throttle Cut
Setting method:
Press the - arrow keys to select the setting item,
and press the plus or minus key to adjust the value.
Click the Back button to exit the interface and save
the settings.
Touch Screen - Click to select the setting item
switching option, (click the value) and click the
setting button on the right to edit the parameter.
Click on the function name in the upper left corner to
exit the interface and save the settings.
In order to get the best flight condition when
operating the throttle stick, a 9-point pitch curve can
be set, and each point can be adjusted from -150%
to +150%.
● The pitch curve can be set to normal, stunt 1,
stunt 2, and throttle hold.
● Normal, Stunt 1, Stunt 2, Throttle lock switch
can be set in the [Fly Mode] and [Throttle Hold]
screens in advance.
Note:
Regardless of the position of the stunt switch,
once the throttle hold switch is turned on, the hover
function is prioritized.
The standard curve setting is centered on
hovering. With the throttle curve (Normal), the
number of engine revolutions is fixed, making the up
and down control the easiest.
(Reference adjustment method for stunt 1/2
curve)
The pitch curve at the high throttle position is set
to the maximum curve that does not burden the
engine. The pitch curve at the low throttle is
matched with the roll, the tendon, the 3D, etc., and
the curve can be divided according to the action.
Turn on the effect 1/2 curve.
(How to adjust the throttle hold curve)
The throttle hold curve is typically used when the
spin landing is lowered. Set the pitch in the middle
according to the action of the stick when the pitch is
raised.
[Notice during operation]
When the engine is started, the special function
switch must be turned off to start the engine at idle
down.
Enter the interface:
→ Model Menu →
WFLY
Pitch Curve.
Example of pitch curve setting:
* Curve Edit Point: In Advanced Curve Editing,
click the Curve Point Value button to switch.
* Throttle rate(RATE); Throttle position (POS).
* In the actual setting process, please set
according to the values specified in the model
helicopter manual.
Idle1
T
h
ro
tt
le R
a
te
Throttle Position
Normal
Idle2
Hovering
Pitch Curve (Helicopter)
Throttle Cut (Helicopter)
-50
-
10 0
-
150
0
+50
+1 0 0
+1 5 0
位置
+
0
%
比率
+
0
%
R X
NO R M
4 . 2V
Pitch Curve
+10 0 %
Rate
+0 %
EXP
N O R M
0 0 : 0 6 : 5 9
-50
-
1 00
-
150
0
+50
+1 00
+1 50
位置
+
0
%
比率
+
0
%
R X
NO R M
4.2V
Pitch Curve
-100 %
Rate
ADV
1/9
0 0 : 0 6 : 5 9
-50
-
100
-
150
0
+50
+100
+150
POS
+
0
%
RATE
+
0
%
-50
-
100
-
150
0
+50
+100
+150
POS
+
0
%
RATE
+
0
%
-50
-
100
-
150
0
+50
+100
+150
POS
+
0
%
RATE
-10
%
-50
-
100
-
150
0
+50
+100
+150
POS
+
0
%
RATE
+
0
%
模拟器
R X
NO R M
混控
4.2V
+120
%
I
NH
Status
+12 0
%
SA
+12 0
%
Switch
Rate
Throttle
Throttle Cut
0 0 : 0 6 : 5 9
The throttle position where the
function is released (the value
on the right indicates the current
throttle stick position.)
Adjust the throttle cut position
(here adjust the throttle servo or
ESC completely)
Model Menu
