Wfly ET07 Instruction Manual Download

Page: 40 / 55

R X

NORM

4 . 2 V

00 :06:59

Rx:5

Ext:12V

ET07

Mo d el1

U s e r N a m e

T 4

The trim step shows the adjustment step value of

the trim adjustment button (T1\T2\T3\T4). The step
value of the trim adjustment can be selected between
1 and 250. According to the performance of the model
type and the purpose of the trim adjustment, a more
suitable step value can be set, and the conventional
model model is set between 2 and 10.

Note: The larger the step value, the fewer times you

need to finish the entire range change when trimming.

V2:

Press down twice to automatically return to the

middle. Normal, it will automatically return to the
middle after release. P&T will not automatically return
to the neutral.

Linkage:

For example, after T1 is linked, the trim

step of channel 1 will follow the action.

T1-T4:

When T1-T4 is needed, when the switch is

used, the switch bar is set to the required servo
position (2nd servo or 3rd servo). After the setting is
finished, the trim state will be displayed in the home
interface.

Enter the interface:

→ General Menu→ trim

WFLY

Step

Setting method:
Press the key-arrow key to select the setting item,

and press the plus or minus key to adjust the value.
Exit the interface and saves the settings after click the
Back button

Touch Screen-Click to select the setting item and

click the value, click the setting button on the right to
edit the value. Click on the function name in the upper
left corner to exit the interface and save the settings.

Trim Step

The auxiliary channel function can change the

switch that has been set on the CH5-CH10, and the
knob can be changed according to personal
preference (can be turned off). It can be selected
from the switches T1-T4, SA-SD, V1 knob, and V2
pulsator. When the control channel of the auxiliary
channel is set to T1-T4, you can set the step value of
the trim in the [Trim Step] function, or set the 2nd or
3rd switching mode.

Enter the interface:

→General Menu →

WFLY

Aux Channel

NO RM

4.2V

Aux Channel

0 0: 0 6 : 5 9

Gyro

CH10

PIT

CH7

CH8

CH9

INH

Ctrl

The channel delay function is mainly used for

realistic actions, such as the retraction of the
landing gear. The channel delay is used to reduce
the response speed of the output channel. The
setting range is 0 to 4 seconds. The default is 0
seconds. The delay time from the low end to the
highest end of the corresponding channel rocker
position is the set time.

Note:

The larger the value displayed on the

interface, the greater the delay and the slower the
action output.

Enter the interface:

→ General Menu →

WFLY

Channel Delay

R X

NO R M

4 . 2V

Channel

Delay

AIL

ELE

THR

PIT

CH7

CH8

CH9

CH10

RUD

Gyro

0 0 : 0 6 : 5 9

End Point

The end point function is used to set the initial

rudder angle of each rudder surface of the body. The
amount of servo movement can be adjusted
separately on the left and right sides.

The left and right direction of the servo can be

adjusted between 30% and 155%, and the maximum
limit can be adjusted between 0% and 155%.

Note:

The actual rotation of each channel servo is

displayed on the interface. The display of the neutral
position is based on the setting value of Sub-Trim
Therefore, the adjustment of the Sub-Trim will affect
the upper and lower limit points of the servo.

Enter the interface:

→General

WFLY

Menu→End Point

Setting method:
Press the key- arrow keys to select the setting

item, press the plus or minus key to adjust the value,
and press the confirm key to switch the function
status and mode. Exit the interface and saves the
settings after click the Back button

Touch Screen-Click to select the setting item and

switch the setting item status and mode, click the
value and click the setting button on the right to edit
the value. Click on the function name in the upper
left corner to exit the interface and save the settings.

100

155

NORM

4.2V

End Piont

0 0: 06 : 5 9

1 35 %

L i m i t

T r a v e l

T r a v el

L i mit

AIL