38
00 00 0
:
.
00 00 0
:
.
R X
NO R M
4.2V
ET07
00:06 :59
0
0
0
0
Rx:3.7V
Ext:3.7V
Mod e l1
U se r Na m e
The ET07 has two separate timers available.
The timer can be used for a variety of timings,
such as the running time of the engine or power
battery, race timing, and the like.
You can set the timing, countdown, and the beep
will sound if the set target timing is completed.
(When the countdown or positive timing reaches the
last 20 seconds, a continuous short beep will start,
and when the timing is finished, a long beep will
sound. The timing will sound every minute.)
Can only reset timer by resetting the timer
.
The control methods can be assigned the
following three types:
1 Throttle:
Set the position where the throttle is
turn on. The start and stop of the timer is controlled
by the throttle stick ("Above 50%": the throttle is
above 50% to start the timer, otherwise the timer is
paused; "Below 50%": the throttle is below 50% to
start the timer On the contrary, the timeout is
suspended.)
2 Switch:
Set the name of the control switch. The
start and pause of the timer are controlled by the
switch.
3 Power on:
The timer starts when the transmitter
is turned on.
Timer on the standby interface:
Timer 1 cannot be set to switch control
Timer 2 belongs to the controllable timer
described on this page.
Interface path:
→ General Menu→ Timer
WFLY
Setting method:
Press the key-arrow keys to select the setting
item, press the plus or minus key to adjust the
value, and press the enter key to switch the
function status and mode. Exits the interface and
saves the setting after the click Back button.
Touch Screen-Click the button to select the
setting item and switch the setting item status and
mode, click the value and click the setting button on
the right to edit the value. Click on the function
name in the upper left corner to exit the interface
and save the settings.
(Acquisition of throttle position: Select the value
of the throttle position, click the "confirm" button
or click the button where the value is located to
obtain the parameter of the stick position!)
1 When selected, "Confirm button" and tap and
hold to stop timing and reset the value, click to start
or pause timing.
2 When selected, "Confirm button" and press &
hold to reset the value.
Timer
模拟器
R X
NORM
混控
4 . 2 V
10
U p
INH
Mode
Time
Contrl
Position
0 0
M
S
Switch
Timer
Status
0 0: 06: 59
SB
Throttle,
switch,
power on
Click to switch
模拟器
R X
NO R M
混控
4 . 2V
10
U p
INH
Mode
Time
Contrl
Position
0 0
M
S
Throttle
Timer
Status
0 0 : 0 6 : 5 9
Up
50
%
模拟器
R X
NO R M
混控
4 . 2V
10
U p
INH
Mode
Time
Contrl
Position
0 0
M
S
Throttle
Timer
Status
0 0 : 0 6 : 5 9
Down
50
%
Throttle
Up
Throttle
Down
①
②
General Menu
When set to "Throttle" control, the interface is as
follows:
When the position is "Up", click the parameter
(button) on the right to intercept the trigger position.
For the example of the figure, set to 50%, when the
throttle is greater than (above) the set position, the
status is on and the timer starts counting.
When the position is "down", click the parameter
(button) on the right to intercept the trigger
position. For the example of the figure, set to 50%,
when the throttle is less than (below) the set
position, the status is on and the timer starts
counting.
