49
The throttle hold setting function can fix the
throttle servo in the low speed position when the
flameout is executed, and the throttle hold position
can be adjusted within ±75%. The preset switch
(custom) is responsible for switching this function.
Note:
The throttle hold position needs to be
applied according to the specific conditions of the
model.
Interface Path:
→ Model Menu→ Throttle
WFLY
Hold
Setting method:
Press the - arrow keys to select the setting item,
and press the plus or minus key to adjust the value.
Click the Back button to exit the interface and save
the settings.
Touch Screen - Click to select the setting item
switching option, (click the value) and click the
setting button on the right to edit the parameter.
Click on the function name in the upper left corner to
exit the interface and save the settings.
Throttle Hold (Helicopter)
This function adjusts the throttle output curve for
the throttle stick motion through a 9-point curve to
achieve the best flight/engine speed. Each point can
be adjusted from -25 to 125%.
● The curve can be set under normal, Idle 1, Idle
2, and throttle hold conditions.
● Normal, Idle 1, Idle 2, Throttle hold switch,
preset in the fly mode interface. (Normal throttle
curve adjustment method) The ordinary throttle
curve is "the basic throttle curve made with hovering
as the center. With the normal pitch curve, the
number of engine revolutions is fixed, so that the
upper and lower control can be used for the simplest
purpose". (Normal, Idle 1, Adjusting Method of
Throttle Curve of Idle 2) The Idle curve setting is to
allow the helicopter to maintain a certain number of
revolutions even when the pitch is operated while
the helicopter is flying at high altitude. Match the
movement curve of the tendon, roll, 3D, etc., and
then use the normal, Idle 1, and Idle 2 separately
according to different actions.
Note:
You must start the engine with normal idle
speed under normal mode(Shut down Idle) while the
engine is starting
Interface Path:
→ Model Menu→ Throttle
WFLY
Curve
Setting method:
Press the - arrow keys to select the setting item,
and press the plus or minus key to adjust the value.
Click the Back button to exit the interface and save
the settings.
Touch Screen - Click to select the setting item
switching option, (click the value) and click the
setting button on the right to edit the parameter.
Click on the function name in the upper left corner to
exit the interface and save the settings.
Throttle curve setting example:
* Curve Edit Point: In Advanced Curve Editing,
click the Curve Point Value button to switch.
* Throttle ratio (RATE); throttle position (POS).
* During the actual setting process, please set
according to the values specified in the model
helicopter manual. and click the setting button on
the right to edit the parameter. Click on the function
name in the upper left corner to exit the interface
and save the settings.
T
h
ro
tt
le R
a
te
Throttle Position
Normal
IDLE1
IDLE2
Throtle Curve (Helicopter)
R X
NO R M
4 . 2 V
Throttle Curve
+ 10 0 %
Rate
+0 %
EXP
N O R M
0 0 : 0 6: 59
+25
+
0
-
25
+
5 0
+75
+ 1 0 0
+ 1 2 5
PO S
+
5 0
%
RATE
+
50
%
1/ 9
0%
Rate
ADV
0 0 : 0 6 : 5 9
+25
+
0
-
25
+
5 0
+75
+10 0
+12 5
PO S
+
50
%
RAT E
+
50
%
R X
NO R M
4.2V
Throttle Curve
+25
+
0
-
25
+
50
+75
+100
+125
POS
+
5 0
%
RA TE
+
50
%
+2 5
+
0
-
2 5
+
5 0
+7 5
+ 1 00
+ 1 50
POS
+
50
%
RATE
+
50
%
+25
+
0
-
25
+
50
+75
+100
+150
PI S
+
50
%
R A TE
+
65
%
RX
NORM
4.2 V
I
NH
SA
Switch
Throttle Hold
Status
+0%
Pos
0 0: 06: 5 9
Model Menu
