Westport WEST ADR 80/02 User Manual Download Page 24

Page: 24 / 91

2.3. WEST HARDWARE SETUP

CAUTION

Extended operation with altered system variables may reduce the

life of system components. Limit troubleshooting time with

variables altered.

CAUTION

Only have the WEST hardware connected while the vehicle is

being serviced by trained personnel.

CAUTION

Never allow the service harness to be severed by the door or

damaged in any way. If the insulation on the harness is crushed or

damaged, replace the harness immediately. A short inside this

harness may result in the vehicle shutting off unexpectedly.

CAUTION

If the CAN to USB converter enclosure becomes damaged,

exposing the electronics, replace the CANUSB Dongle

immediately.

CAUTION

If at any point WEST loses communication with the computer

due to the USB cable being disconnected, WEST will prompt a

message. The message informs the user that the USB cable has

been disconnected and the user will need to reconnect it and

restart WEST (Fig. 2.10).

WEST User Manual

Summary of Contents for WEST ADR 80/02




























































































Search results

Summary of Contents for WEST ADR 80/02

Reviews:

Related manuals for WEST ADR 80/02

Brands by name

Popular brands

Westport WEST ADR 80/02, User Manual

Search results

Summary of Contents for WEST ADR 80/02

Reviews:

Related manuals for WEST ADR 80/02

Brands by name

Popular brands