![background image](http://html.mh-extra.com/html/wen/tt1015/tt1015_instruction-manual_956583006.webp)
TABLE SAW SAFETY
1. Never place your hands in the vicinity of, or in line
with, the saw blade.
2. Always wear ANSI Z87.1 approved eye protection, as
well as hearing protection and respiratory protection.
3. Avoid kickback. Keep the blade sharp and the rip
fence parallel to the saw blade. Make sure the riving
knife, anti-kickback devices, and the blade guard are in
place, properly aligned, and functional. Do not release
a workpiece before passing it completely through the
blade. Do not rip a workpiece that is twisted or warped.
Do not attempt to pull the workpiece backwards out of a
cut while the blade is still turning.
4. Always use a properly functioning saw blade guard,
riving knife and anti-kickback device for every operation
for which it can be used, including all through sawing.
5. Use a push-stick or push-block when required, espe-
cially when ripping narrow workpieces. A push stick is
supplied with the saw.
6. Do not perform any operation freehand. Always use
the fence, miter gauge, or both to support and guide the
workpiece.
7. Pay particular attention to instructions on reducing
the risk of kickback.
8. Never reach around or over the saw blade.
9. Turn off tool and wait for the saw blade to come to
a complete stop before moving workpiece or changing
settings.
10. Never stand directly in line with the saw blade. Al-
ways position your body on the same side of the saw
blade as the fence.
11. Support large panels to minimize the risk of blade
pinching or kickback.
12. Keep hands out of the line of the saw blade.
13.
DON'T USE IN DANGEROUS ENVIRONMENT.
Don't
use power tools in damp or wet locations, or expose
them to rain. Keep work area well lit. Do not use power
tools in the presence of flammable liquids or gases.
14.
MAKE WORKSHOP KID PROOF
with padlocks, mas-
ter switches, or by removing starter keys.
15.
USE THE RIGHT TOOL.
Don't force tool or attach-
ment to do a job for which it was not designed.
16.
WEAR PROPER APPAREL.
Do not wear loose cloth-
ing, gloves, neckties, rings, bracelets, or other jewelry
which may get caught in moving parts. Nonslip foot-
wear is recommended. Tie back long hair.
17.
CHECK DAMAGED PARTS.
Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate prop-
erly and perform its intended function - check for align-
ment of moving parts, binding of moving parts, break-
age of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
18.
REMOVE ALL ACCESSORIES
from the table prior to
transporting the saw.
19.
DANGER - NEVER
attempt to free a stalled blade
without first turning the saw OFF and unplugging it.
20.
PROVIDE ADEQUATE SUPPORT
to long or wide
workpieces.
21.
AVOID AWKWARD OPERATIONS
and hand posi-
tions, where a sudden slip could cause your hand to
move into the blade or its path.
22.
SECURELY MOUNT THE TABLE SAW
to a workbench
or stand before performing any cutting operations.
23.
NEVER CUT METALS
or any material that creates
hazardous dust.
SAW BLADE SAFETY
1. Always wear protective gloves when handling saw
blades.
2. Only use blades with correct size and type for both
your table saw and your workpiece.
• The rated diameter of the saw blade is 10 inches
with a 5/8 inch arbor.
• The no-load speed of the table saw is 4800 RPM.
The maximum permissible speed of your saw blade
should always be higher than the no-load rotational
speed of the saw.
SPECIFIC RULES FOR YOUR TABLE SAW
WARNING!
Do not operate the power tool until you have read and understood the following instructions
and the warning labels.
6
Summary of Contents for TT1015
Page 38: ...38 NOTES ...
Page 39: ...39 NOTES ...