![background image](http://html.mh-extra.com/html/wen/tt1015/tt1015_instruction-manual_956583009.webp)
9
SPECIFIC RULES FOR YOUR TABLE SAW
WARNING!
Do not operate the power tool until you have read and understood the following instructions
and the warning labels.
10. When restarting the saw with the saw blade in the
workpiece, center the saw blade in the kerf so that the
saw teeth are not engaged in the material. If the saw
blade binds, it may lift up the workpiece and cause kick-
back when the saw is restarted.
11. Keep saw blades clean, sharp, and with sufficient
set. Never use warped saw blades or saw blades with
cracked or broken teeth. Sharp and properly set saw
blades minimize binding, stalling and kickback.
TABLE SAW OPERATION WARNINGS
1. Turn off the table saw and disconnect the power cord
when removing the table insert, changing the saw blade
or making adjustments to the riving knife, ant kickback
device or saw blade guard, and when the machine is
left unattended. Precautionary measures will avoid ac-
cidents.
2. Never leave the table saw running unattended. Turn it
off and don’t leave the tool until it comes to a complete
stop. An unattended running saw is an uncontrolled
hazard.
3. Locate the table saw in a well-lit and level area where
you can maintain good footing and balance. It should be
installed in an area that provides enough room to easily
handle the size of your workpiece. Cramped, dark areas,
and uneven or slippery floors invite accidents.
4. Frequently clean and remove sawdust from under the
saw table and/or the dust collection device. Accumu-
lated sawdust is combustible and may self-ignite.
5. The table saw must be secured. A table saw that is
not properly secured may move or tip over. Mount it
securely to a benchtop or stand before cutting.
6. Remove tools, wood scraps, etc. from the table be-
fore the table saw is turned on. Distraction or a potential
jam can be dangerous.
7. Always use saw blades with correct size and shape
(diamond versus round) of arbor holes. Saw blades that
do not match the mounting hardware of the saw will run
off-center, causing loss of control.
8. Never use damaged or incorrect saw blade mount-
ing means such as flanges, saw blade washers, bolts or
nuts. These mounting means were specially designed
for your saw, for safe operation and optimum perfor-
mance.
9. Never stand on the table saw, do not use it as a step-
ping stool. Serious injury could occur if the tool is tipped
or if the cutting tool is accidentally contacted.
10. Make sure that the saw blade is installed to rotate in
the proper direction. Do not use grinding wheels, wire
brushes, or abrasive wheels on a table saw. Improper
saw blade installation or use of accessories not recom-
mended may cause serious injury.
CAUTION:
This means that if precautions are not heed-
ed, it may result in minor or moderate injury and/or
possible machine damage.
WARNING:
This means that if precautions are not
heeded, it could result in serious injury or possibly even
death.
WARNING:
The operation of any power tool can result
in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning pow-
er tool operation, always wear safety goggles or safety
glasses with side shields and a full face shield when
needed. Always use eye protection which is marked to
comply with ANSI Z87.1.
WARNING:
If the power cord requires replacement, this
must be done by the manufacturer.
WARNING:
Only cut wood on this table saw. Do not cut
any plastic and metal on this saw.
WARNING:
Always keep guards in place and in proper
operating condition.
WARNING:
Use blade guard for every applicable opera-
tion including all through cuts. If the guard is removed
for special non-through cuts, such as dado or rabbet
cuts, replace the blade guard before further use of the
saw.
WARNING:
Keep hands out of the line of the saw blade.
Never reach around or over the saw blade.
Summary of Contents for TT1015
Page 38: ...38 NOTES ...
Page 39: ...39 NOTES ...