Welch Allyn Propaq LT 802LT0N Service Manual Download Page 38

Page: 38 / 80

Disassembly and reassembly

Welch Allyn Propaq LT Vital Signs Monitor

Disassembling the top chassis

The top chassis assembly contains the top plastic panel assembly (including the
integrated overlay for buttons, window, LEDs, and trim), the display module, and the
speaker.

“Removing the lithium ion battery assembly”

on page 29.

“Separating the top and bottom chassis halves”

on page 31.

Remove the display module.

Remove the four screws from the display bracket, and remove the bracket to free
the display module.

Remove the display module.

REASSEMBLY:

Tighten the display bracket screws to a torque of 2 inch lbs. Take care to avoid stripping
the plastic screw mounts.

Caution

Take care to protect the front surface of the display module and all

surfaces of the display screen from scratching and contamination.

Display module (back side)

Bracket

Bracket screws

REASSEMBLY: The display module cable lies under the bracket.

Reassembly: 2 inch lbs

Gaskets

Summary of Contents for Propaq LT 802LT0N

















































































Search results

Summary of Contents for Propaq LT 802LT0N

Reviews:

Related manuals for Propaq LT 802LT0N

Brands by name

Popular brands

Welch Allyn Propaq LT 802LT0N, Service Manual

Search results

Summary of Contents for Propaq LT 802LT0N

Reviews:

Related manuals for Propaq LT 802LT0N

Brands by name

Popular brands