Welch Allyn Propaq LT 802LT0N Service Manual Download Page 31 | Manualshive

Page: 31 / 80

background image

Service Manual

Disassembly and reassembly

27

Connectors

Zero insertion force (ZIF) flex cable connectors

ZIF connectors use a sliding outer piece that latches and unlatches to secure and release
the flex cable. ZIF cables cannot be successfully connected or disconnected without
properly unlatching and latching the sliding outer piece.

To disconnect a ZIF cable

1.

Using a suitable tool (paper clip, small flat-blade screwdriver, or small needle-nose
pliers), slide the latching piece of the connector away from the connector body and
toward the cable, releasing the cable from the connector.

2.

Remove the cable.

To connect a ZIF cable

1.

Slide the latching piece of the connector body away from the body.

Note

All connectors are keyed or labeled to facilitate proper connection. Take care to
correctly align all connector halves before attempting to connect them.

«
...
29
30
31
32
33
...
»

Summary of Contents for Propaq LT 802LT0N

















































































Reviews:

No comments

Related manuals for Propaq LT 802LT0N

Brand: Gardner Bender Pages: 7

Brand: QMI Pages: 54

Brand: M-system Pages: 18

Brand: Omega Pages: 31

Brand: Sensia Pages: 139

Brand: York Pages: 2

Brand: RaySafe Pages: 2

AUER Atemluft 300 bar

Brand: MSA Pages: 52

Photo Set Strato S-20

Brand: Fisso Pages: 2

Brand: Carman Pages: 64

Brand: SMPE Pages: 2

Brand: Banner Pages: 4

Brand: Hanna Instruments Pages: 21

touchMATRIX WDG 053XIOM

Brand: Wachendorff Pages: 48

Brand: Hanna Instruments Pages: 2

Brand: Hameg Pages: 6

Brand: TA ENGINEERING Pages: 22

Brand: Liquivision Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands