Welch Allyn Propaq LT 802LT0N Service Manual Download Page 33 | Manualshive

Page: 33 / 80

background image

Service Manual

Disassembly and reassembly

29

Procedures

Removing the lithium ion battery assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Replacing the air filter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Separating the top and bottom chassis halves

. . . . . . . . . . . . . . . . . . . . . . . . . 31

Disassembling the top chassis

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Removing the main board from the bottom chassis assembly

. . . . . . . . . . . . . 36

Removing the NIBP assembly from the main board

. . . . . . . . . . . . . . . . . . . . . 41

Removing the patient connector panel from the bottom chassis

. . . . . . . . . . . 45

Removing the power/USB flex connector from the bottom chassis

. . . . . . . . . 46

Disassembling the cradle

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Removing the lithium ion battery assembly

in

The battery pack assembly consists of the rechargeable lithium ion cells, a protection
board, and the battery door. It can be replaced only as an assembly.

1.

Remove the two screws securing the battery door.

2.

Remove the battery assembly from the battery compartment.

WARNING

The lithium ion battery can deliver currents sufficient to cause

serious personal injury and to damage the monitor. Before opening the monitor
for any reason, and before you begin any procedure described in this manual,
always remove the battery first.

WARNING

The only safe method for charging the monitor battery is to insert the

completely assembled monitor, with the completely assembled battery pack
correctly installed, into the completely assembled charging cradle. Attempting to
charge the monitor battery by any other method creates a significant risk of
explosion or patient shock hazard.

WARNING

Do not short the battery connector pins.

WARNING

Do not attempt to disassemble the battery. The battery pack

contains no user-serviceable parts.

Note

When the monitor, the cradle, or the battery reaches end of life, recycle it locally
according to national, state, and local regulations, or return it to Welch Allyn.

Two screws securing
the battery door
Reassembly: 2 inch lbs

«
...
31
32
33
34
35
...
»

Summary of Contents for Propaq LT 802LT0N

















































































Reviews:

No comments

Related manuals for Propaq LT 802LT0N

Brand: rainforest Pages: 2

Brand: Kawai Pages: 5

Brand: Jata hogar Pages: 12

Brand: Candela Pages: 4

Brand: Quantel Pages: 2

Power Xpert PXM 4000

Brand: Eaton Pages: 28

Brand: National Instruments Pages: 38

Brand: Vega Pages: 20

Brand: Vega Pages: 16

Brand: Vega Pages: 2

Brand: Wagner Meters Pages: 17

Brand: X-laser Pages: 17

Brand: DAKOTA ULTRASONICS Pages: 38

Brand: SKF Pages: 12

Stream Line Pro

Brand: Halo Photonics Pages: 45

Stubby LED-1500

Brand: Dive Perfect Pages: 4

Brand: SBS Pages: 17

Photo Set Strato S-20

Brand: Fisso Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands