Welch Allyn Propaq LT 802LT0N Service Manual Download Page 35

Page: 35 / 80

Service Manual

Disassembly and reassembly

If the O-ring shows signs of wear, replace it with a new one.

REASSEMBLY:

Lubricate the outside of the O-ring with a drop of alcohol to prevent it from riding up the
side of the cylinder when inserted.

When properly installed, the filter cylinder is perfectly flush with the chassis surface.

Separating the top and bottom chassis halves

“Removing the lithium ion battery assembly”

on page 29.

Remove the four cylindrical rubber plugs from the screw holes in the bottom chassis.

REASSEMBLY:

When reinstalling the rubber plugs, lubricate the screw holes with water applied with a
damp cotton swab.

Air filter

Cylinder flush with
chassis surface

Rubber plugs removed

Summary of Contents for Propaq LT 802LT0N

















































































Search results

Summary of Contents for Propaq LT 802LT0N

Reviews:

Related manuals for Propaq LT 802LT0N

Brands by name

Popular brands

Welch Allyn Propaq LT 802LT0N, Service Manual

Search results

Summary of Contents for Propaq LT 802LT0N

Reviews:

Related manuals for Propaq LT 802LT0N

Brands by name

Popular brands