Welbilt FRYMASTER FilterQuick FQE30 Installation, Operation And Maintenance Manual Download | Manualshive

Page: 36 / 44

background image

6-6

6.2.6 Error Log Codes (For FilterQuick™ Controller Only)

CODE

ERROR MESSAGE

EXPLANATION

E03 ERROR TEMP PROBE

FAILURE

Temp probe reading out of range

E04

HI 2 BAD

High limit reading is out of range.

E05

HOT HI 1

High limit temperature is past more than 410°F (210°C), or in CE
countries, 395°F (202°C)

E06 HEATING

FAILURE

A component has failed such as controller, interface board, gas
valve, ignition module or open-high limit.

E07

ERROR MIB SOFTWARE

Internal MIB software error

E08

ERROR ATO BOARD

ATO board connection lost; ATO board failure

E09

ERROR PUMP NOT FILLING Dirty paper/pad and it needs changed or it was bypassed; filter

pump problem

E10

ERROR DRAIN VALVE NOT
OPEN

Drain valve was trying to open and confirmation is missing

E11

ERROR DRAIN VALVE NOT
CLOSED

Drain valve was trying to close and confirmation is missing

E12 ERROR RETURN VALVE

NOT OPEN

Return valve was trying to open and confirmation is missing

E13 ERROR RETURN VALVE

NOT CLOSED

Return valve was trying to close and confirmation is missing

E14

ERROR AIF BOARD

MIB detects AIF missing; AIF board failure

E15

ERROR MIB BOARD

Cooking controller detects MIB connections lost; Check software
version on each controller. If versions are missing, check CAN
connections between each controller; MIB board failure

E16

ERROR AIF PROBE

AIF RTD reading out of range

E17

ERROR ATO PROBE

ATO RTD reading out of range

E20

INVALID CODE LOCATION

SD card removed during update

E21

FILTER PAPER PROCEDURE
ERROR (Change Filter Paper)

25 hour timer has expired or a dirty filter may be causing an
incomplete filtration.

E22

OIL IN PAN ERROR

Oil may be present in the filter pan.

E25

RECOVERY FAULT

Recovery time exceeded maximum time limit. Recovery time
should not exceed 1:40 for electric.

E27

LOW TEMP ALARM

Oil temperature has dropped 30°F (17°C) lower than setpoint in
idle mode or 45°F (25°C) in cook mode. (This message may
appear if a product is dropped and the start cook button is not
pressed immediately or if too large of cook loads are dropped.)

E28

HIGH TEMP ALARM

Oil temperature has risen 40°F (22.2°C) higher than
setpoint. If temperature continues to rise, the high limit will shut the
burner off when temperature reaches 425°F (218°C) Non-CE or
395°F (202°C) CE.

E70

OQS TEMP HIGH

Oil temperature is too high for a valid OQS reading. Filter at a
temperature between 300ºF (149ºC) and 375ºF (191ºC).

«
...
34
35
36
37
38
...
»

Summary of Contents for FRYMASTER FilterQuick FQE30













































Reviews:

No comments

Related manuals for FRYMASTER FilterQuick FQE30

Brand: Zanussi Pages: 19

home HG LS 1000

Brand: Somogyi Pages: 38

Vision Tech VTV 580NC

Brand: Hoover Pages: 14

Frialator SF14 UFM

Brand: Pitco Pages: 43

Global Design 815U

Brand: Toastmaster Pages: 16

Brand: GoWISE USA Pages: 16

Brand: Roper Pages: 16

DVE50R5400 Series

Brand: Samung Pages: 120

Brand: Alliance Laundry Systems Pages: 30

Brand: ADA GASTROGAZ Pages: 18

Brand: Indesit Pages: 84

Brand: Tricity Bendix Pages: 18

Brand: AEG Pages: 64

Brand: AEG Pages: 28

Frymaster FilterQuick 2FQG30U

Brand: Welbilt Pages: 80

Brand: LAVATHERM Pages: 28

Brand: Indesit Pages: 64

Brand: Devair Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands