Welbilt FRYMASTER FilterQuick FQE30 Installation, Operation And Maintenance Manual Download

Page: 33 / 44

6-3

Problem

Probable Causes

Corrective Action

Controller display is in

wrong temperature

scale (Fahrenheit or

Celsius).

Incorrect display option programmed.

Fryers using the FilterQuick controller
can toggle between F° to C° by pressing
the



button until Product setup is

displayed. Press



to scroll to Tech

Mode and press



. Enter 1658. Press the

scan button. The controller displays

OFF

. Turn the controller on to check

temperature. If the desired scale is not
displayed, repeat.

Controller displays

temp.

Frypot temperature is more than 40 ºF
(4ºC).

Press the power button to turn off fryer
and let cool before returning power to
fryer. If issue continues call your FAS
for assistance.

Controller display

shows

hot-hi-1

Frypot temperature is more than 410ºF
(210ºC) or, in CE countries, 395ºF
(202ºC).

Shut the fryer down immediately and
call your FAS for assistance.

Controller displays

High limit

failure

disconnect

power

Failed high limit

Shut the fryer down immediately and
call your FAS for assistance.

Controller display

shows

TEMP

PROBE FAILURE.

Problem with the temperature
measuring circuitry including the probe
or damaged controller wiring harness or
connector.

Shut the fryer down and call your FAS
for assistance.

Controller display

shows

HEATING

FAILURE.

Failed controller, failed interface board,
open high-limit thermostat.

Call your FAS for assistance.

Heating indicator is

on, but fryer is not

heating.

Three phase power cord unplugged or
circuit breaker is tripped.

Verify that the main power cord is fully
seated in its receptacle, locked into place
and that circuit breaker is not tripped If
the problem continues call your FAS for
assistance.

Controller displays

RECOVERY

FAULT/ YES

and

alarm sounds.

Recovery time exceeded maximum time
limit.

Clear error and silence the alarm by
pressing the



(YES) button.. Maximum

recovery time for electric is 1:40. If this
error continues call your FAS for
assistance.

Controller locks up.

Controller error.

Call your FAS for assistance.

Controller displays

SERVICE

REQUIRED

followed

by an error message

An error has occurred which requires a
service technician.

Press the



(YES) button if the issue is

fixed or press the



(NO) button to

continue cooking and call your FAS for
assistance. In some cases, cooking may
not be available..

Summary of Contents for FRYMASTER FilterQuick FQE30













































Search results

Summary of Contents for FRYMASTER FilterQuick FQE30

Reviews:

Related manuals for FRYMASTER FilterQuick FQE30

Brands by name

Popular brands

Welbilt FRYMASTER FilterQuick FQE30, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for FRYMASTER FilterQuick FQE30

Reviews:

Related manuals for FRYMASTER FilterQuick FQE30

Brands by name

Popular brands