Welbilt FRYMASTER FilterQuick FQE30 Installation, Operation And Maintenance Manual Download

Page: 35 / 44

6-5

Problem

Probable Causes

Corrective Action

filtration won’t

start.

Check that MIB board is not
in manual mode.

Check to see that the MIB
cover is not damaged and
depressing the buttons.

Filter relay has failed.

sensor.

Ensure MIB board is in “A” automatic
mode. Power cycle the fryer.

Remove and replace cover and see if
filtration will start.

Call your FAS for assistance.

Controller display

shows

filter

busy

Another filtration cycle or filter

paper change is still in process.

Wait until the previous filtration cycle ends to
start another filtration cycle. Change filter
paper if prompted.

6.2.4 Basket Lift Problems

Problem

Probable Causes

Corrective Action

Basket lift movement is

jerky and/or noisy.

Basket lift rods need lubrication.

Apply a light coating of Lubriplate

™

or similar

lightweight white grease to the rod and bushings.

6.2.5 Auto Top-Off Problems

Problem

Probable Causes

Corrective Action

Frypots won’t top off.

A.  Crumb build up around sensor.
B. Fryer temperature too low.
C.  Oil is too cold.
D.  JIB out of oil
E. A fryer may be unplugged or fryer

with ATO box may not have power.

F. Service required error exists

Clean crumbs from opening
surrounding sensor.

B. Fryer temperature must be at

setpoint.

C. Ensure that the oil in the JIB is

above 70°F (21°C).

D. Ensure the JIB is not out of oil and

supply line is in the JIB. Replace
JIB and press the



button when

prompted and press and hold the
ORANGE reset button for ten (10)
seconds to reset top off system.

If problem persists call your FAS
for assistance.

Check plugs, breakers and

switches.
F. Call your FAS for assistance.

One vat doesn’t top

off.

Filter error exists.

Service required error exists

Solenoid, pump, pin issue, RTD or
ATO issue.

Clear filter error properly. If
problem persists call your FAS for
assistance.

Call your FAS for assistance.

Controller displays

TOPOFF OIL

EMPTY /

CONFIRM

Top off system out of oil.

Fill top off system with oil and press
the



(CONFIRM) button. Once the

JIB is replaced press and hold the
orange reset button for ten (10)
seconds to reset top off system.

Summary of Contents for FRYMASTER FilterQuick FQE30













































Search results

Summary of Contents for FRYMASTER FilterQuick FQE30

Reviews:

Related manuals for FRYMASTER FilterQuick FQE30

Brands by name

Popular brands

Welbilt FRYMASTER FilterQuick FQE30, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for FRYMASTER FilterQuick FQE30

Reviews:

Related manuals for FRYMASTER FilterQuick FQE30

Brands by name

Popular brands