Waupaca Paca-Ryde Installation Instructions Manual Download Page 41

Page: 41 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTE10200-A

13 MAR 2018

Series:

008, 021, 022, 114, 115, 116, 118, 210

LED Light Wiring

(With-out battery back up wiring)

Strip the LED extension cord back to the desired length. Wire per LED light schematic and national

and local codes terminating one LED light per terminal.

Verify that all LED lights work and adjust the dimmer to desired brightness.

Secure the LED Light covers and power supply to the ceiling of the elevator car with provided

hardware.

NOTE:

THERE ARE 9 SETS OF TERMINAL BLOCKS, EACH WITH 3 CONDUCTORS PER LIGHT. FOR SIMPLICITY, ONLY 1 SET IS SHOWN IN THIS

DIAGRAM. ALWAYS CONNECT ALL 3 WIRES (RED, BLACK, YELLOW), EVEN IF DIMMING IS NOT REQUIRED.

TO TURN LIGHTS ON AND OFF, SIMPLY ENERGIZE OR DE-ENERGIZE THE 120/240V AC INPUT TO THE EL2 POWER BOX.

ATTENTION: REMOVE ALL JUMPERS AS REQUIRED OUT OF THE LED LIGHT CONTROLLER BOX

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

FALLING

HAZARD

ANTI-

STATIC

ALERT

WITH-OUT BATTERY BACK-UP WIRING

(STANDARD)

Power Supply

DC Wiring

RED

BLK

RED

BLK

RED

BLK

RED

BLK

RED

BLK

RED

BLK

RED

BLK

RED

BLK

RED

BLK

Dim

Brown

Blue

Green & Yellow

Black

White

Yellow Dim Control

Red Dim Control

Black Dim Control

To Lights

120-240V

AC FEED

(Switched)

WARNING: DO NOT MIX AC AND DC WIRING. MAINTAIN BARRIER AS SHOWN BY THE DOTTED LINE

Input and output conductors are to be insulated for a minimum of 300V for all circuit connections.

Page 41

Summary of Contents for Paca-Ryde









































































Search results

Summary of Contents for Paca-Ryde

Reviews:

Related manuals for Paca-Ryde

Brands by name

Popular brands

Waupaca Paca-Ryde, Installation Instructions Manual

Search results

Summary of Contents for Paca-Ryde

Reviews:

Related manuals for Paca-Ryde

Brands by name

Popular brands