Waupaca Paca-Ryde Installation Instructions Manual Download Page 18

Page: 18 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTM30125-E

7 FEB 2018

DO NOT RUN ELEVATOR WITHOUT THE FINAL LIMIT SWITCH INSTALLED!

Screw

FINAL LIMIT

INSTALLATION

SERIES :

114, 116

3, 6

Position the top fi nal limit switch

assembly in the desired location at the

top of the elevator hoistway. Only the

switch arm from the assembly must

make contact with the elevator and shall

fully actuate before the elevator hits any

obstruction. (i.e., ceiling, electrical and/

or mechanical part, etc.)

Fasten the fi nal limit switch assembly

to the hoistway with the appropriate

hardware.

Loosen the screw and open cover. Verify

the normally closed contacts with a

multi-meter.

Wire to the previously verifi ed normally

closed terminals. All wiring must meet

N.E.C. and local codes.

Note:

Do not over tighten

terminals. Terminals should be

torqued to 7lb-in max.

Verify the operation of the fi nal limit

switch.

Replace cover and refasten screw.

Adjust as necessary, the fi nal limit switch

assembly may move or need adjustment

after the elevator car is installed.

Wire to Terminals TF1and TF2

ANTI-

STATIC

ALERT

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

ELECTRIC

HAZARD

FALLING

HAZARD

PINCH

HAZARD

Torque the

Normally

Closed

Terminals

to 7lb-in max.

Note:

Verify the switch actuates and

disconnects power to the driving
machine before the elevator is at its
max extent or strikes any obstruction.

Page 18

Summary of Contents for Paca-Ryde









































































Search results

Summary of Contents for Paca-Ryde

Reviews:

Related manuals for Paca-Ryde

Brands by name

Popular brands

Waupaca Paca-Ryde, Installation Instructions Manual

Search results

Summary of Contents for Paca-Ryde

Reviews:

Related manuals for Paca-Ryde

Brands by name

Popular brands