manualshive.com logo in svg

Waters ACQUITY Arc System, System Manual, Page: 11 / 86

Share
Download
Waters ACQUITY Arc System System Manual Download Page 11

B Solvent considerations ................................................................69

B.1 Preventing contamination ..............................................................................69

B.1.1 Clean solvents ....................................................................................69
B.1.2 Solvent quality....................................................................................69
B.1.3 Solvent preparation .............................................................................69
B.1.4 Water ................................................................................................70

B.2 Common solvent properties ...........................................................................70

B.2.1 Solvent miscibility ...............................................................................72
B.2.2 Solvent stabilizers ...............................................................................74
B.2.3 Solvent viscosity .................................................................................74
B.2.4 Wavelength selection ...........................................................................74

C Specifications ..............................................................................80

C.1 System specifications....................................................................................80

C.2 Quaternary Solvent Manager-R specifications ...................................................80

C.3 Sample Manager FTN-R specifications .............................................................82

C.4 30-cm Column heater and 30-cm Column heater and column heater/cooler

specifications ...............................................................................................83

C.5 30-cm Column Heater-Active (CH-30A) specifications........................................84

C.6 Instrument control specifications ....................................................................84

C.7 Environmental specifications ..........................................................................85

C.8 Electrical specifications..................................................................................85

C.9 Physical specifications ...................................................................................85

June 12, 2015, 715004747 Rev. A

Page xi

Summary of Contents for ACQUITY Arc System























































































Reviews:

No comments